5: An aluminum rod (E-70 GPa and v=0.25) is inserted into a hollow steel tube (E=210 Gra and v-0.28). The aluminum rod projects (015 mm) as shown and has a diameter of (40 mm). The steel tube has an inside diameter of (50 mm) and is (10 mm) thick. If the applied load (P= 200 kN), determine: 1) The axial stresses in the aluminum rod and the steel tube. 2) Load carried by each bar. 3) The change in diameter of the aluminum. P. 0.15mm 250mm Aluminum

5: An aluminum rod (E-70 GPa and v=0.25) is inserted into a hollow steel tube (E=210 Gra and v-0.28). The aluminum rod projects (015 mm) as shown and has a diameter of (40 mm). The steel tube has an inside diameter of (50 mm) and is (10 mm) thick. If the applied load (P= 200 kN), determine: 1) The axial stresses in the aluminum rod and the steel tube. 2) Load carried by each bar. 3) The change in diameter of the aluminum. P. 0.15mm 250mm Aluminum

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
0.6 m 1.2 m 3.1 The rigid bar af negligible weight is supported as shown in the figure. If W= 80 kN, compute the temperature change of the assembly that will cause a ten- sile stress of 50 MPa in the steel rod. Use the following data: Bronze 3 m Steel 5 m A (mm) a (1°C) E (GPa) H10m Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is
A cylinder of (320) mm inside diameter and (64) mm thickness is subjected to an internal pressure of 15 MPa. Find the variation of circumferential and radial stresses in the shell and plot them. What is the increase in the inside and outside diameters of the shell? Take E=200 GPa and v=0.3
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 500 mm, b = 250 mm, h = 330 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 130 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax (1) a i ● 1.418 B ● ● b kN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 560 mm, b = 280 mm, h = 450 mm, and 0= 70%. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a Answer: Pmax= i B KN
Determine the nodal displacements and the element stresses. E = 105 GPa, v = 0.3, and t = 5 mm. You don't have to calculate everything manually, but can write a code to get some input from you and find the stiffness matrices for instance. 400 mm 3 5 400 mm 30 kN 2
The rectangular bar is connected to the support bracket with a 25-mm-diameter pin. The bar width is w = 65 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax i kN
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips. Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.Answer: F1 = ? kips.
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
For the assembly, the temperature rises by 35°C after a load W = 140 kN is applied. Assume the horizontal bar will not deform. apronze=18.9µm/m "C and a steel=11.7µm/m°C. Determine the stress in each of the vertical rods. Bronze L= 3 m A = 1300 mm2 E = 83 GPa Steel L= 1.5 m A = 320 mm2 E = 200 GPa 1 m 2.5 m 1.5 m
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 14 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 4 kips, R = 16 kips and S = 28 kips. A (1) VQ В R| (2) S S C (3) D First: Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.