5-46 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Determine (a) the change in kinetic energy, (b) the power output, and (c) the turbine inlet area. Answers: (a) -1.95 kJ/kg, (b) 12.1 MW, (c) 0.0130 m² P₁ = 4 MPa T₁ = 500°C V₁ = 80 m/s

5-46 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Determine (a) the change in kinetic energy, (b) the power output, and (c) the turbine inlet area. Answers: (a) -1.95 kJ/kg, (b) 12.1 MW, (c) 0.0130 m² P₁ = 4 MPa T₁ = 500°C V₁ = 80 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a wind turbine that is situated in an area that has steady winds. The turbine rotates at 16 RPM. The mass flow rate through the turbine is 41,025 kg/s. The tip velocity is 260 km/hr. Take the air density to be 1.31 kg/m² and assume 180kW of electric power is generated by the turbine. Determine the following: a. Average velocity of the air b. The efficiency of the turbine c. Assuming winds are steady for 95% of the year, is this a suitable location for a wind turbine? Explain.
Steam enters a nozzle at 600 °C and 1200 kPa with a velocity of 13 m/s and leaves at 400 °C and 600 kPa while losing heat at a rate of 26 kW For an inlet area of 870 cm2 determine the velocity and the volume flow rate of the steam at the nozzle exit. rks ME 203 ons Steam V2 = 599 899 m/s volume flow rate = 2678 m/s V2 = 619 002 mis yolume flow rate = 3 152 m ls V2 = 914 995 m/s
Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10MPa, 400°C, and 100 m/s, and the exit conditions are 10 kPa, 88 percent quality, and 50m/s. The mass flow rate of the steam is 18 kg/s. Determine (a) the change in kinetic energy,(b) the power output, and (c) the turbine inlet area.
Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10MPa, 400°C, and 100 m/s, and the exit conditions are 10 kPa, 89N percent quality, and 50m/s. The mass flow rate of the steam is 19N kg/s. Determine (a) the change in kinetic energy,(b) the power output, and (c) the turbine inlet area.
A pump increases the water pressure from 8 kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51℃ through a 1.122-cm-diameter opening and exits through a 2.709-cm-dameter opening Determine the velocity of the water at the outlet in m/s hen the mass flow rate through the pump is 1.693 kg/s. The specific volume of incoming water is 1.038x10^-3 m^3/kg.
A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 285 psf, and 270 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,255 psf and 750 degrees Fahrenheit. Assuming that the velocity found at the inlet is 6,285 feet per minute and the Heat supplied is 580 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 6 minutes?
R-134a enters a compressor as a saturated vapor at 80 kPa and exits at a pressure of 400 kPa. If 44 kJ/kg of work is required and 5 kJ/kg of heat is lost to the surroundings. What is the outlet temperature. Round your answer to the nearest whole number.
A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty pound- mass per minute of air at 220 psf, and 250 degrees Fahrenheit. The fluid is discharged from a point five meters above the datum/ reference point at 4,275 psf and 750 degrees Fahrenheit. Assuming that the velocity found at the inlet is 8,275 feet per minute and the Heat supplied is 580 BTU/min. During the process the density decreases by 15 percent and the internal energy is decreased by 1.05 horsepower. Determine the Work done in (a) Horsepower and BTU/s. (b) Considering the given on 3a, if the Work done is doubled, determine the Heat supplied during the process? (c) Considering the given on 3b, if Heat is doubled, what is the work done after 7 minutes?
5-51 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Determine (a) the change in kinetic energy, (b) the power output, and (c) the turbine inlet area. P₁ = 4 MPa T₁ = 500°C V₁ = 80 m/s Steam m = 12 kg/s P₂ = 30 kPa X₂ = 0.92 V₂ = 50 m/s W out
A pump increases the water presssure from 8kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51 degrees celsius through a 1.145-cm-diameter opening and exits through a 2.821-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.354kg/s. The specific volume of incoming water is 1.547x10-3m3/kg.
Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s.