I need the solution on the paper please n41 In Fig. 10-37, two particles, cach with mass m = 0.85 kg, are fastened to each other,and to a rotation axis at O, by two thin rods, each withlength d = 5.6 cm and mass M = 1.2 kg. Thecombination rotates around the rotation axis with theangular speed w =0.30 rad/s. Measured about O, whatare the combination's (a) rotational inertia and (b)kinetic energy?стRotation axisChapter 11: Rolling, Torque and Angular Momentum

Given: Mass of the particles is 0.85 kg Length is 5.6 cm and mass of the rod id 1.2 kg The angular…

Answered: *41 In Fig. 10-37, two particles, each…

Similar questions

Fuel oil in a day tank for use of an industrial boiler is tested with a hydrometer. The hydrometer reading indicates an SG = 0.919 when the temperature of the oil in the tank is 40°C. Calculate the higher heating value of the fuel using ASME formula.
To what temperature must a gas sample initially at 27°C be raised in order for the average energy of it's molecule to triple?
There are two important isotopes of uranium, 235 U and 238 U ; these isotopes are nearly identical chemically but have different atomic masses. Only 235 U is very useful in nuclear reactors. Separating the isotopes is called uranium enrichment (and is often in the news as of this writing, because of concerns that some countries are enriching uranium with the goal of making nuclear weapons.) One of the techniques for enrichment, gas diffusion, is based on the different molecular speeds of uranium hexafluoride gas, UF6 . (a) The molar masses of 235 U and 238 UF6 are 349.0 g/mol and 352.0 g/mol, respectively. What is the ratio of their typical speeds vrms ? (b) At what temperature would their typical speeds differ by1.00 m/s? (c) Do your answers in this problem imply that this technique may be difficult?
The molecular formula of aspartame, the artificial sweetener marketed as NutraSweet Ⓡ, is C14H18 N2O5. How many moles of aspartame are present in 4.50 mg of aspartame? Express your answer using three significant figures. | ΑΣΦ n= ? mol
A gas thermometer registers an absolute pressure of 305 mm of mercury when in contact with water at the triple point. What pressure does it read when in contact with water at the normal boiling point?
Mercury is the only metal that exists as a liquid (d=13.56 g/cm3) at room temperature. Find the number of moles in 15 mL of mercury.
We're told oxygen is the most common element in the Earth's solid crust. But how much oxygen is there? Let's compare to the amount of oxygen in the Earth's atmosphere, like this: • The most common minerals in the Earth's crust are feldspars, and albite (NaAlSi,0g) is a typical feldspar. Let's assume the entire crust is made of albite with a density of 2.6 g/cm°. • The radius of the Earth is 6371. km and let's say the crust is the upper 100. km of it. • Let's model the Earth's atmosphere as a layer on top of the Earth about 100. km thick with an average density of 0.99 g/m", and which is 23.1% oxygen by mass. Use this information to calculate the ratio of the mass of oxygen in the Earth's atmosphere to the mass of oxygen in the Earth's crust. Round your answer to 2 significant digits.
Two large tanks, each holding 100L of liquid, are interconnected by pipes, with the liquid flowing from tank A into tank B at a rate of 3L/min and from B into A at a rate of 1L/min. The liquid inside each tank is kept well stirred. A brine solution with a concentration of 0.1kg/L of salt flows into tank A at a rate of 6L/min. The (diluted) solution flows out of the system from tank A at 4L/min and from tank B at 2L/min. If initially, tank A contains pure water and tank B contains 10kg of salt, determine the mass of salt in each tank at time t≥0. What is the solution to the system? x(t)= y(t)=
Helpful formula: Q = mcΔT - please solve this on a sheet of paper.
Assume that a raindrop has a volume of 0.05 cm^3 and you need an Avogadro's number of raindrops to fill up the cubic water tank. What is the length of the edge of the tank?
In a vacuum chamber designed for surface-science experiments, the pressure of residual gas is kept as low as possible so that surfaces can be kept clean. The coverage of a surface by a single monolayer requires about 10 19 atoms per m². What pressure would be needed to deposit less than one monolayer per hour from residual gas? You may assume that if a molecule hits the surface, it sticks.
How to find the number of atoms in an iron cylinder given its mass(g)?