find axial force, shear force and bending moment diagrams for the following structure 40kN/m EBIm40 kN/m↓ ↓ ↓4mD↓↓Im☑3m√ 100 kN.m90kN2m5mNote: Members BC and CD are rigidly connected;the hinge at C only isolates member CF

answers and diagrams are provided on the picture uploaded below. please don't forget to rate :)…

Answered: 40kN/m E B Im 40 kN/m ↓ ↓ ↓ 4m D ↓ ↓ Im…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

FIGURE PS-55 25 K 15 K 6 ft 4 ft 3.0K/ft 4 Use the free body diagram pproach shown in Sections 5-3 through 5-5 to determin the internal shearing force and bending moment al any speecified point in a beam. nd bending moneat diagrams using the guidelines pre- sented in Section 5-10.
i need the answer quickly
i need the answer quickly
Given l= 1000 mm and P= 4000 N, draw internal shear force and moment diagram.
Draw Shear Force and Bending Moment Diagram Graphically for the following Beam
The beam is subjected to a point load and a distribution load as shown in Figure 2-1 below, and the right end is a build-in support. (1ft=12inch, ksi=kilo lb/in2)(a) Find the reaction in build-in support C.(b) Draw a Shear Force Diagram in the beam BC interval.(c) Draw a Moment Diagram in the beam BC interval.(d) Find the maximum shear stress mmax in the beam BC interval.(e) Find the maximum tensile flexural stress mmax, T and maximum compressive flexural stress mmax, C in the beam BC interval, respectively.
A steel beam ABC carries a uniformly distributed load of w (kN/m) over the unsupported length BC, as shown in Figure Q3(a). The beam has a wide-flange section shown in Figure Q3(b) and designated as W610 x 82 with geometrical properties as shown in Table 1. Assuming that the beam behaves as elastic-perfectly plastic material with a yield strength of 210 MPa; (a) Draw the moment diagram of the beam and indicate the section that carries the maximum bending moment. (b) Knowing the shape factor of the beam, k = 1.15 calculate the magnitude of wp (kN/m) for the condition of plastic collapse/hinge. (c) Determine the yielded length, L, (m) along the beam where the section has experienced yielding corresponding to the plastic collapse condition (part (b)). W (kN/m) -10 m (a) (b) Figure Q3 Table 1 Wide-Flange Sections or W Shapes SI Units Flange X-x axis y-y axis Web Area Depth thickness width thickness Designation A tw by mm x kg/m mm? 10° mm 10 mm 10° mm 10 mm mm mm mm mm mm mm W610 x 155 19…
Need help with this Q.
Q3: For the load diagram shown in figure (2) below, the first contraflexure point of the bending moment diagram is located at ... m from A. 50 kN 60 kN/m 8 KN.m 2 m 4 m 2 m Figure (2)
The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is oy=418 MPa, whereas that used for the rectangular cross- section is 0.70y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 84 mm, b=46 mm, a=11 mm, H=84 mm, d= 46 mm Z || Part a) b N.mm h Z mm d 1. The numerical value of plastic section modulus of the solid rectangular section is mm ³ H 2. The numerical value of plastic moment of the solid rectangular section is Part b) calculate the value of t The numerical value of t can be calculated as
The figure below shows a cable supporting a beam. In addition there is a vertical force acting on the right end of the beam. L Calculate the normal force N(x), the shear force V (x), the moment M(x) as a function of the parameters L and f. (Partial Answer: N(x) = 2f for 0
The beam is subjected to a point load and a distribution load as shown in Figure 3-1 below. (a) Find the reaction from supports B and E.(b) Draw a beam's Shear Force Diagram.(c) Draw the moment diagram of the beam.(d) If the cross-sectional area is shown in Figure 3-2, how many mm is the neural axis NA from the bottom? (e) Find the second moment of area, INA from the neural axis.(f) Find the maximum shear stress mmax from the beam.(g) Find the maximum tensile flexural stress mmax, T and maximum compressive flexural stress mmax, C on the beam, respectively.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

40kN/m E B Im 40 kN/m ↓ ↓ ↓ 4m D ↓ ↓ Im ☑ 3m √ 100 kN.m 90kN 2m 5m Note: Members BC and CD are rigidly connected; the hinge at C only isolates member CF