A simply supported beam of a total length l is shown in Figure Q5, where point A is supported by a pin connection and point C is supported by a roller support. The concentrated load is P at the location of 21/3. Determine the shear-force and bending-moment distributions produced in the beam by the concentrated load P. Note that adatpive marking has been used to consider the method mark. P 21 3 – x A C • y В Figure Q5: A simply supported beam with a concentrated load applied

A simply supported beam of a total length l is shown in Figure Q5, where point A is supported by a pin connection and point C is supported by a roller support. The concentrated load is P at the location of 21/3. Determine the shear-force and bending-moment distributions produced in the beam by the concentrated load P. Note that adatpive marking has been used to consider the method mark. P 21 3 – x A C • y В Figure Q5: A simply supported beam with a concentrated load applied

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.16P: Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.

See similar textbooks

Related questions

Q: 4. Draw the complete shear and bending moment diagrams. -2 m- 15 kN] 20 kN.m 10 kN/m -2 m- B

Q: Assume the following : wb W = 100N/m; a = 5m; b = 8m; c = 6m %3D (1-5)Max. Moment occurs @ x = _(fr…

Q: Determine the shear stress and bending moment lines under load as shown in the figure below.

Q: 2. For the 20 meter beam shown, there is a roller at "A" (Ay = 52 kN; it is acting upward), and a…

A: For the 20 meter beam shown, there is a roller at "A" (Ay= 52 KN; it is acting upward), and a pin…

Q: Find the shear force and bending moment at points B and D. Note: B lies just to the right of the 150…

Q: For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment…

Q: 3. In Problem 2 beam has a cross-section as shown below. Moment of inertia of the cross section is…

A: The moment of inertia of cross-section is I=450 in4. The centroid location is 9.9 in from bottom.…

Q: Given a=2.4m, b=1.9m, c=1.5m, d=1.9m, P=14kN, Q=28kN, w=3kN/m, and Moment M=4 kN.m in the direction…

Q: B P = 10 kN L = 2.5 m 1.4 What is the value of the bending moment at x = 1.5 m?

Q: For the beam shown in the figure, Calculate the support reaction forces and find the internal forces…

Q: For the following figure, calculate the shear stress, V, when x = 12.0 m. Draw the Shear Force and…

Q: Problem 6 Draw the shear force and bending moment diagrams. values: a = b = 4 ft, c= d = 2 ft, P =…

A: The values are

Question

Given l= 1000 mm and P= 4000 N, draw internal shear force and moment diagram.

A simply supported beam of a total length l is shown in Figure Q5, where point A is
supported by a pin connection and point C is supported by a roller support. The
concentrated load is P at the location of 21/3. Determine the shear-force and
bending-moment distributions produced in the beam by the concentrated load P.
Note that adatpive marking has been used to consider the method mark.
P
21
3
– x
A
C
y
В
Figure Q5: A simply supported beam with a concentrated load applied

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Use answer from first part without spring to build onto next part, thanks.
Give the expressions of the shear and moment at an arbitrary poistion x of BC segment, be careful of the sign.
Need help with this Q.
For the beam and loading shown in Figure 5, determine the value of (r) at the point of action of the resuitant force of the distributed load using point B as the origin. Parabola Vertex 2000 N/m 900 N/m B 6 m A Figure 5: A parabolic distributed load on a beam AB. Answer: If the loading were analysed using point A as the origin, would the value of w at the location of the resultant change? Select one: a. No b. Yes
I’m struggling with this question I’m please
1. Find the maximum bending stress - and find the factor of safety 2. find with using the general hear formula - shear stress - and find the factor of saefty
A propped cantilever beam is loaded by a bending moment of the magnitude M_B at the point B as shown in Figure Q1. The cross-section of the beam is a rectangle of the width w and the hight ℎ that are constant along the length of the beam L. The beam material’s Young’s modulus is Q. Assuming the positive deflections and positive vertical reaction forces are upward, calculate the value of the reaction forces at points A and B the absolute value of the reaction bending moment at point A A) Let R represent the reaction force at Support B. By releasing the beam at Support B and imposing a force R at Point B, the deflection of the beam consists of two parts,i.e. Part I- the deflection caused by M_B ; Part II- the deflection caused by R Please treat R, w, h , L , E as variables in this step , the mathematical equation for the deflection at Point B caused by R ( Part II) can be written as: b) Using the provided data: cross-section width w = 14 mm, cross-section hight h = 82…
A propped cantilever beam is loaded by a bending moment of the magnitude M_B at the point B as shown in Figure Q1. The cross-section of the beam is a rectangle of the width w and the hight ℎ that are constant along the length of the beam L. The beam material’s Young’s modulus is Q. Assuming the positive deflections and positive vertical reaction forces are upward, calculate the value of the reaction forces at points A and B the absolute value of the reaction bending moment at point A A) Let R represent the reaction force at Support B. By releasing the beam at Support B and imposing a force R at Point B, the deflection of the beam consists of two parts,i.e. Part I- the deflection caused by M_B ; Part II- the deflection caused by R Please treat R, w, h , L , E as variables in this step , the mathematical equation for the deflection at Point B caused by R ( Part II) can be written as: b) Using the provided data: cross-section width w = 14 mm, cross-section hight h = 82…
In Figure Q3a, a beam is supported at A and C with a uniformly distributed load of20 kN/m between A and B. Draw and label the shear force diagram (SFD) andbending moment diagram (BMD) for the beam shown in Figure Q3a. Label thevalues for shear force and bending moment at points A, B, C & at the beam midpoint M; the maximum bending moment and its distance from A; and clearlyindicate the type of bending between AB and between BC
The dimensions are of the graph are d1 = 7 cm , L1 = 6 m , d2 = 4.2 cm , and L2 = 5 m with applied loads F1 = 130 kN and F2 = 60 kN . The modulus of elasticity is E = 80 GPa . Use the following steps to find the deflection at point D. Point B is halfway between points A and C. What is the reaction force at A? Let a positive reaction force be to the right.
For the same beam and loading case in Figure Q1, which of the following best describes the mostaqREDdiate method for finding the vertical deflection for any point along its length? Oa Use the Tresca criterion. Ob. Form an equation for the bending moment as a function of x - writing some terms using Macaulay notation - and then use double integration. OC Apply Euler's theory of buckling. O d Apply Castigliano's theorem. O. Form an equation for the bending moment as a function of x and then use double integration (Macaulay notation is NOT required for this problem). OF. None of the provided answers are correct.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy