-40 cm- L- 20 cm The rod with varying circular cross sectional area is subjected to the force P as shown in the figure. Modulus of elasticity (Young's Modulus) of the rod material is E. Determine horizontal the displacement of point A.

Q: what is the formula used in the -δp + δt = -δp + δt = -δp + δt part at the top? what is the…

A: Given:  (-δp + δt)A = (-δp + δt)B = (-δp + δt)C Required: To explain the  δp and δt meaning in the…

Q: 2.) Find also the principal stresses oi and oz and its orientations 0p1 and 0p2 from the x-axis.…

A:

Q: The sectional dimension of a reinforced concrete short column is b X h= 400 mm X 400 mm. The length…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Calculate the breaking stress (

A: Given:  Side of concrete cube, a=15 cm = 150 mm Load at time of breaking, P kN = 1000*P N To find :…

Q: Provide the ASTM for Specific Weight of ff: a. Fine Aggregate b. Coarse Aggregate:

A: Here it is asked to provide the ASTM Specification for Specific Weight of following:1. Fine…

Q: 3. (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A: shear stress : Shear stress is a force that tends to distort a material by causing it to slip along…

Q: Three proposed cross-section configurations for joining three boards are shown in Figure 1. Each…

A: Given, b = 50 + 29 + 9 = 88 mm  Mz = 5000 Nm or 5 x 106 N-mm

Q: A steel rod 30 mm X 20 mm is subjected to an axial load of 35 kN. The original length of the rod is…

A: Given data : Original length (L)=650 mmDecrease in length (∆L)=-5 mmAxial load (P)=35 KNDimension=30…

Q: A 12 mm steel bar is hanged vertically as shown and is loaded with a 700 lb weight of scrap…

A:

Q: From the figure below, (a) determine the allowable stress using the yield strength (0.2% offset) and…

A: Using the figure, the allowable stress ( 0.2% offset) with a factor of safety 4 has to be…

Q: An elastoplastic material with strain hardening has the stress–strain relationship shown in Figure .…

A: a) In order to find strain. first, calculate E: Substitute the value in the formula:

Q: Determine the bulk modulus for the following material glass E, - 8 (10³) ksi : v- 0.26 Vg - 5556 ksi…

A:

Q: A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm…

A:

Q: fy = 415 MPa n = 9 Tension reinforcement: 2 – 25mmø RSB 1.4 Pmin fy Pmax = 0.75pp 0.85f:B, (600) Pb…

A: Given : b = 200 mm D = 400 mm, d = 337.50 mm fc = 21 MPa fy = 415 MPa

Q: please get a report. I want you to explain to m

A:

Q: The 70-30 bruss used for a certain application should bave a minimum tensile strength of 50ksi, and…

A: To determine the percentage of cold work required to achieve the specified properties, we can use…

Q: Generally Ring and ball test is performed on which material ?

A: ring and ball test experiment is done for bituminous material for softening point. purpose of the…

Q: have more strain, a 10ft bar being stretched 3 inches or a 3ft bar being stretched 3 inches? It…

A: Stretching a material causes it to experience strain, which is determined by the material's original…

Q: How to prevent retained austensite

A: By controlling the below parameters we can prevent retained austensite. It is very necessary in…

Q: Given: A steel rod (A = 150mm^2) is stretched between two fixed points with a tensile load of 5000N…

A:

Q: Calculate the cracking moment as per NSCP 2015 for the given beam shown in the figure given that: bf…

A: Cracking moment The moment that, if surpassed, causes concrete to fracture is known as the "cracking…

Q: 1.3 (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A: SHEAR STRESS: It is defined as the force, internal resisting force per unit area.The force acting on…

Q: For a given elextic material, the Eastic Modulus E is 210 GPa and its Poission's Ratio is 0.27. What…

A:

Q: Monolithic columns have larger surface areas than porous particles. Is true or flase?

A: Rather than beads, the solid phase inside a monolithic column seems to have a constant porous…

Q: civil engineering Article Determine ( ↑ 0.3mm A=1m² केतिला Top plate 2 kinematic viscosity 3…

A:

Q: féz 4000 psi, NWC Grade 60 steel, &#8 Mn = ?

A: Answer  We know that Nominal Moment capacity of singly reinforced beam is given by Mn = As*Fy*z As =…

Q: Problem 4.87 Figure 40 mm r 10 mm 20 mm 5 mm 20 mm ▾ Part A max Value Submit Determine the maximum…

A:

Q: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

A:

Q: The flange of an S275 beam is 53.3 mm thick. What is the yield strength of the beam in N/mm2?…

A: Given, S275 Beam The thickness of flange=53.3 mm

Q: solution

A:

Q: damages concrete is

A: Option  A is the correct answer.    In restoration of strength by adding external reinforced…

Q: Design Average Strength Strength (MPa) Specimen Diameter Batch No. Strength Age (days) (Mpa) Load…

A:

Q: Find out the working stress if a steel column carries a load of 1.6 MN with a factor of safety of 5.…

A: Given data:- The given Ultimate stress of steel, =472 MN/M2 The given factor of safety, =5 The given…

Q: 2. Given a strain gage with these properties: Rg=200 , Sg 2.5, r-2, Vs = 5 V, and Pg=0.015 W.…

A: To determine the sensitivity (Ss) of the strain gauge Wheatstone bridge, we can use the following…

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.