Question: Determine the diameter of the elasticcore of the rod ?Options:A. 13.72 mmB.10.34 mmC.11.57 mmD.12.95 mmA solid steel rod is 1.5 meters long and has a diameter of 20 mm. The steel rod is assume tobe an elastoplastic material with G = 77 GPa and a yield shear stress of 145 MPa.

Given, Length (L) = 1.5 m Diameter (d) = 20 mm

Answered: Question: Determine the diameter of the…

Engineering

Civil Engineering

Question: Determine the diameter of the elastic core of the rod ? Options: A. 13.72 mm B.10.34 mm C.11.57 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Related questions

Q: 2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of…

A: Given Data: Total length of the bar is L=2.4 m The diameter of the left half portion is d1=20 mm The…

Q: Calculate the axial deformation of the Brass cylinder section (BC) shown in Figure 8. The…

A: Cross sectional area of steel, Cross sectional area of brass, Modulus of elasticity of steel,…

Q: A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it…

Q: A 76 mm x 76 mm x 6 mm angular section is welded to a gusset plate having a thickness of 10 mm as…

A: Given data: Agross=929 mm2Fy=248 MPaFu=400 MPa

Q: Question Three Three bars each made of different materials are connected together and welded to…

A: The expression for thermal expansion due to temperature increases is given as δT=α∆TL If F be the…

Q: Part 1 Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated…

Q: 1. The bolt connection shows 8-22mm diameter bolts in a bolt hole diameter of 25 mm and spaced…

A: No of bolts = 8 Bolt dia d = 22 mm Bolt hole dia do = 25 mm Pitch distance p = 100 mm Gauge distance…

Q: rivet diameter is 12 mm, the width of the strap is 150 mm, the strap thickness "s" is 10 mm the…

A: The given data is: Dia=12 mm s=10 mm ζr=140 MPaσra=140 MPaσcr=280 MPaζt=100 MPanumbers of revit, n=2

Q: The two vertical rods attached to the light rigid bar are identical except for length. Before the…

A: As per our guidelines we are supposed to answer only first question. Kindly repost other questions…

Q: The light rigid bar ABCD shown in the × figure is pinned at B and connected to two vertical rods.…

Q: A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter…

A: Bearing strength is the maximum stress load that the unit can hold before the structure fails. But…

Q: The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions…

A: Given Area, A=170mm2 E= 80GGpa = 80x109N/m2= 80x103N/mm2 Formula used deformation = P*L/A*E p- load…

Q: SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the…

A: To determine the bearing stress in each bolt. Given, Diameter of each bolt (d) = 20 mm Magnitude…

Q: P = 8kN. Using N = 3, determine the allowable stress for A501 grade šteel. dimensions (to 1 decimal…

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: The compound bar ABCD has a uniform cross-sectional area of 0.25 in.² When the axial force P is…

Q: The two wooden boards shown in the figure are connected by a 0.5 in. diameter bolt. Washers are…

Q: Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. 3 m…

Q: A tapered rod with length c- 8 m and cross-sectional dimensions a - 297 mm and b-79 mm is carrying…

A: A tappered rectangular rod is given and load is applied in it axially. It has been asked to…

Q: Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axial loads…

A: To find the allowable load , First we need to draw free body diagram then apply the given condition…

Q: Getting measurements from Figure , determine approximate values of the following items for steel…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d =…

Q: 4. For the rods shown, determine (a) the compressive force after a temperature rise of 95°C, (b) the…

Q: Compute the value the shear modulus G of steel whose modulus of elasticity E is 200 GPa and…

Q: PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar.…

Q: (c). A bar of length 1000 mm and diameter 30 mm is centrally bored for 400 mm, the bore diameter…

Q: The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in…

Q: PROBLEM 283 30 kN 90 kN B 30 kN -400 mm - 600 mm- Rod is solid with diameter 30mm.

Q: A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40…

Q: Determine the following for the bar. A) B) C) D) What is the Modulus of Elasticity for the material…

A: Given "

Q: ng data: Aluminum A = 2.6 sq. in Osi L = 17.3 in 1 °F E = 10519262 psi a = 12.73 x 106°F

A: To find the force in each bars -

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hot rolled steel shaft is subjected to a torsional moment that varies from 330 N.m clockwise to 110 N.m counterclockwise and an applied bending moment at a critical section varies from 440 N.m to -220 N.m. The shaft is of uniform cross section and no key way is present at the critical section. Determine the required shaft diameter. The material has an ultimate strength of 550 MN/m2 and yield strength of 410 MN/m2. Take the endurance limit as half the ultimate strength, factor of safety of 2, size factor of 0.85and .a surface finish factor of 0.62 * 39.5mm O 60 mm 70 mm O 42.8 mm (O
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
pre stressed conc. solution pls answer
pre stressed conc. solution pls answer
7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses in the two materials with an applied load of 45,000 lbs. 45,000 lbs 3.5"Ø 3.0"Ø Steel Aluminum
Read the question carefully and give me right solution according to the question.
The modulus of elasticity of "reinforced concrete" in RC design, is O A. 420 GPa B. 200 GPa C. None () D. 220 GPa
Solution w/FBD
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.
Need neat and clean handwritten solution
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION,20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE XDIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF AUNIFORMLY DISTRIBUTED FORCE OF Px=3kN (COMPRESSION), Py=4kN(TENSION) AND Pz=7kN (COMPRESSION) IN THE X, Y AND Z DIRECTIONSRESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa,DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSODETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THEWOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE X DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.