### 4.03-1. Network Address Translation (a)Consider the following scenario in which host 10.0.0.1 is communicating with an external web server at IP address 128.119.40.186. The NAT table shows the table entry associated with this TCP flow. What are the source and destination IP address and port numbers at point A?**Scenario:**- Host IP: 10.0.0.1- External Web Server IP: 128.119.40.186**NAT Translation Table:**| WAN Side Address | LAN Side Address ||------------------|------------------|| 138.76.29.7, 5051 | 10.0.0.1, 2020 |**Diagram Explanation:**- **Point A** is where the data is being transmitted from the LAN side to the WAN side.**Placeholders for the NAT Entry:**- WAN Side IP: 138.76.29.7- WAN Side Port: 5051- LAN Side IP: 10.0.0.1- LAN Side Port: 2020---**Answer the following:**1. **The source IP address is:** - Given: 10.0.0.12. **The destination IP address is:** - Given: 128.119.40.1863. **The source port number is:** - Given: 2020 4. **The destination port number is:** - Given: 5051**Visual Explanation:**The diagram illustrates the flow of data through a network with NAT. The points of interest mark the transition of data packets, with designated source and destination IP addresses and port numbers being translated as they pass through the NAT device.- **Point A** shows the initial connection details from the internal LAN host (10.0.0.1) heading out to the external web server.- The source IP (10.0.0.1) and port (2020) are translated to the external IP (138.76.29.7) and port (5051) by the NAT.**Note:**For further practice problems similar to this, you can refer to the provided link (here).

Below is the answer to above question. I hope this will be helpful for you...

4.03-1. Network Address Translation (a). Consider the following scenario in which host 10.0.0.1 is communicating with an external web server at IP address 128.119.40.186. The NAT table shows the table entry associated with this TCP flow. What are the source and destination IP address and port numbers at point A? [Note: You can find more examples of problems similar to this here.] S: D: B S: NAT translation table WAN side addr 138.76.29.7, 5051 138.76.29.7 The source IP address is: The destination IP address is: The source port number is: The destination port number is: LAN side addr 10.0.0.1, 2020 ****** 10.0.0.4 S D: 10.0.0.1 2020 S: 128.119.40.186 5051 D: 10.0.0.1 10.0.0.2 10.0.0.3

4.03-1. Network Address Translation (a). Consider the following scenario in which host 10.0.0.1 is communicating with an external web server at IP address 128.119.40.186. The NAT table shows the table entry associated with this TCP flow. What are the source and destination IP address and port numbers at point A? [Note: You can find more examples of problems similar to this here.] S: D: B S: NAT translation table WAN side addr 138.76.29.7, 5051 138.76.29.7 The source IP address is: The destination IP address is: The source port number is: The destination port number is: LAN side addr 10.0.0.1, 2020 ****** 10.0.0.4 S D: 10.0.0.1 2020 S: 128.119.40.186 5051 D: 10.0.0.1 10.0.0.2 10.0.0.3

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Consider the subnet address 210.84.40.0, divided into 3 subnets. If we want to maximize the number of hosts per subnet, what subnet mask should we use? What would the numbers of the first 2 and last 2 subnets be, along with their address range and their broadcast? Explain your answers.
2. The following illustration shows a transmission from Host A to Host B using Network Address Translation (NAT). Host A is located inside a Local Area Network (LAN) with an IP address of 192.168.1.2. The LAN is connected to the Wide Area Network (WAN), i.e. the Internet, through a router R1 that conducts NAT. R1 has two interfaces with an internal LAN IP address (192.168.1.1) and and external WAN IP address (127.45.10.35). Host B is located outside the LAN and is a well-known server, e.g., Google's server. Host B has an IP address of 130.160.23.45. Port numbers for the application components running at both hosts are provided in the figure. For a single message M1 being sent from Host A to Host B, please fill in the blanks in the illustration below with the source IP address and Port number at Host A and at the Router R1. Any information not provided may be assumed, however, please state your assumption clearly. Host A Local Area Network (LAN) IP: 192.168.1.2 Port: 5252 Source IP…
Consider transferring an enormous file of L bytes from Host A to Host B. Assume an MSS of 536 bytes. a. What is the maximum value of L such that TCP sequence numbers are not exhausted? Recall that the TCP sequence number field has 4 bytes. b. For the L you obtain in (a), find how long it takes to transmit the file. Assume that a total of 66 bytes of transport, network, and data-link header are added to each segment before the resulting packet is sent out over a 155 Mbps link. Ignore flow control and congestion control so A can pump out the segments back to back and continuously.
14 The following figure shows a TCP transaction. Assume Host A always has data to send, and each packet has size 20 Bytes. Assume Host A has a sending window of 40 Bytes, that is, it can send two "in-flight” packets maximum. Answer the following questions. A. At the time marked "1", i.e., when the first packet times out, will Host A send any packet? if your answer is no, explain why not; if your answer is yes, how many packets will be sent, what are the sequence numbers of them? B. At the time marked "2", i.e., when the ACK of the 2nd packet is received by Host A, will Host A send any packet? if your answer is no, explain why not; if your answer is yes, how many packets will be sent, what are the sequence numbers of them? Host A Host B Seq=80, 20 bytes of data Seq=100, 20 bytes of data Xª 1 2- timeout
Consider the LAN below consisting of 12 computers (A-L) connected by two Ethernet bridges. At t=0 the bridging table entries for both bridges are empty. At t = 1, node L sends to node E, and node E replies immediately (well before the next time step). What are the (MAC address, interface) entries in the bridging tables right after these transmissions? Note: interface = port number a) Left-hand-side bridge: (L,15), (E, 8). Right-hand-side bridge: (L,7), (E, 5). b) Left-hand-side bridge: (L,8), (E, 8). Right-hand-side bridge: (L,7), (E, 7). c) Left-hand-side bridge: (L,15), (E,5). Right-hand-side bridge: (L,7), (E, 8). d) Left-hand-side bridge: (L,8), (E,8). Right-hand-side bridge: (L,7), (E, 7).
Consider the following virtual circuit network with three reserved virtual circuits: уC1: H1, А, С, Е, Н2 VC2: H3, A, F, D, H4 ус3: НЗ, А, F, D, E, H2 Host H4 Host H3 Нost H2 Host H1 Draw the routing table of router D and the routing table of router C. *you may design a table using the HTML editor or write the content of routing table record by record (record per line).
Below are the two questions, so make sure to answer each part carefully and label the response for each question: 1) Why does TCP implement congestion control if it already has flow control to manage the sender's window? 2) Consider our recent reading [Chiu+89] Analysis of the Increase and Decrease algorithms for congestion avoidance in computer networks. How does this article showcases that TCP is fair?
1. What is the difference between packet fragmentation (i.e., at network layer) and frame frag- mentation (i.e., at link layer) in terms of purpose? 2. Suppose that host A is connected to a router R1, R1 is connected to another router, R2, and R2 is connected to host B. Suppose that a TCP message that contains 800 bytes of data and 20 bytes of TCP header is passed to the IP function at host A for delivery to B. Show the Total length, DF, MF, and Fragment offset fields of the IP header in each packet transmitted over the three links. (Assume that link A-R1 can support a maximum frame size of 1024 bytes including a 14-byte frame header, link R1-R2 can support a maximum frame size of 512 bytes, including an 8-byte frame header, and link R2-B can support a maximum frame size of 432 bytes including a 12-byte frame header.) (*hint: the Fragment offset field is denominated by 8-bytes, not bytes) 3. What is the purpose of the path MTU discovery process (see textbook Figure 5-42) and why does…
A protocol stack used by many applications is to use TCP at the transport layer and IP at the network layer. The ICMP protocol is also used to report on problems encountered by IP. A) The IP protocol provides a service referred to as "best effort". Describe the services of IP and potentially ICMP protocol, with respect to flow control( ensuring the sender does not overwhelm the receiver). B) Describe the services TCP provides with respect to flow control and explain the mechanisms it uses to overcome the deficiencies of IP.
Assume the maximum transmission unit (or MTU) of an IP packet on 100 Mbps Ethernet is set at 1500 bytes. Also, assume we are sending our file using IPv6 at the Network layer and UDP at the Transport layer. A typical IPv6 header consists of 40 bytes, a UDP header consists of 8 bytes. Answer the following three questions based on the information provided above. For all answers, enter a decimal integer value without formatting (no commas). 1. How many packets do we have to send in order to transfer a file of 24KB over 100 Mbps Ethernet? packets 2. How many bytes do we have to send at the network layer in order to transfer the above file entirely? bytes 3. How many bytes do we have to send at the data link layer in order to transfer the above file entirely? Assume that the Ethernet header is 14 bytes and the frame checksum is 4 bytes. bytes
Refer to the network figure above, showing two Ethernet Subnets connected through an IP Router, answer the following question 1-5. The devices in each subnet are connected locally to each other through layer two intermediate devices such as Ethernet switch and ethernet hub. For each device in the subnets, both its Internet Protocol (IP )address and its MAC address (also called the Physical address or the Ethernet address are shown. The subnet mask used by all devices is 255.255.255.240 (which is the same as the prefix length “/28”). 1. If Client #1 wants to send a broadcast packet to all the devices on the left subnet (containing client #1, client #2, client #3) what destination IP address should be used? (Mention in both binary and decimal format.) 2. What is the first and last assignable IP address for the left subnet above (containing client #1 and #3)? (Mention in both binary and decimal format.)
39. The figure below shows the TCP Congestion Window for various transmission rounds of a TCP connection. 20 18 16 14 12 10 4 2 2 4 6 10 12 14 16 18 20 Transmission Round How many more (or less) segments will TCP Tahoe send compared to TCP Reno between the transmission rounds 12 and 16 inclusive (i.e., t12 to t16) for the same sequence of events as shown in the graph above (i.e., loss events at t11, tl4 and t16)? a. TCP Tahoe send 13 less segments compared to TCP Reno b. TCP Tahoe send 20 more segments compared to TCP Reno c. TCP Tahoe send 13 more segments compared to TCP Reno d. TCP Tahoe send 20 less segments compared to TCP Reno e. TCP Tahoe send 28 less segments compared to TCP Reno Congestion Window (MSS) 00