4. Through a refinery, fuel oil is flowing in a pipe at a velocíty of 7.5 m/s and a pressure of 202600 Pa. The pipe increased 5 m in height on a higher level. The diameter of the inlet pipe is 0.8 m and the outlet of the pipe is 0.95 m. The velocity of inlet and outlet are not the same. Determine the pressure at the outlet of the pipe if the density of fuel oil is 750 kg/m3 and gravity g is 9.8 m/s?.

4. Through a refinery, fuel oil is flowing in a pipe at a velocíty of 7.5 m/s and a pressure of 202600 Pa. The pipe increased 5 m in height on a higher level. The diameter of the inlet pipe is 0.8 m and the outlet of the pipe is 0.95 m. The velocity of inlet and outlet are not the same. Determine the pressure at the outlet of the pipe if the density of fuel oil is 750 kg/m3 and gravity g is 9.8 m/s?.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water level in a tank is 20 m above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, and the gage pressure of the air above the water surface is 2.0265 bar. The system is at sea level. Determine the maximum height to which the water stream could rise.
A pitot-static tube is used to measure the velocity of air flowing through a duct. The manometer shows a difference in the head of 5 cm of water. If the density of air and water is 1.13 kg/m3 and 1000 kg/m³ determine the velocity of air. Assume the coefficient of the pitot tube as 0.98. Head in meters The velocity of air in m/s
B
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i. Determine Delta Z (Z2 - Z1) in ft. ii. What is the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s. iii. What is the mass flow rate of the water in lbm/s?
Please verify my answer
The water is flowing through pipe of varying section 1 & 2 with a diameter of 10 cm and 23 cm respectively. If the velocity of water flowing through the pipe at section 1 is 4.5 m/s. Determine (i) The discharge of through the pipe (litres/sec), (ii) The velocity at section 2 (in m/s) .
fluid mechanics Water at 20°C is flowing through a horizontal nozzle at a flow rate of 0.005 m3/s. At the nozzle inlet, the diameter is 5 cm and the pressure is 200 kPag. The nozzle discharges freely to outside air. Determine the velocity of the water (in m/s) as it exits the nozzle. Assume negligible head losses through the nozzle. Round your answer to 2 decimal places.
The water level in a tank is 20 m above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, and the air pressure above the water surface is 2 atm gage. The system is at sea level. Determine the maximum height to which the water stream could rise.
A large, open-topped water tank is being filled from above by a 1.0-cm-diameter hose. The water in the hose has a uniform speed of 11 cm/s. Meanwhile, the tank springs a leak at the bottom. The hole has a diameter of 0.70 cm. Determine the equilibrium level heq of the water in the tank, O measured relative to the bottom, if water continues flowing into the tank at the same rate. heq 1.26 X10-3 Incorrect m
Water flows through a corner valve at a flow rate of Q=0.75 m³/s . The pressure just upstream of the valve is P₁ = 500 kPa and the pressure just downstream is P₂ = 300 kPa. The inside pipe diameters of the valve inlet and exit are respectively, D₁ = 5 cm and D₂ = 12 cm. If the flow through the valve occurs in a horizontal plane, determine the head loss, h₂ (in meters) and the rate of loss of available energy (in W) across the valve. D2 Di
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. a. Assuming that the large open reservoir is open to the atmosphere as well, what is the mechanical energy balance eq for the system? b. What is the Reynolds number for the flow ?