4. Steam undergoes an adiabatic expansion in a piston-cylinder assembly from 100 bar, 360 C to 1 bar, 160 C. What is work in kJ per kg of steam for the process? Calculate the amount of entropy produced, in kJ/K per kg of steam. What is the maximum theoretical work that could be obtained from the given initial state to the same final pressure? Show both processes on a properly labeled sketch of the T-s diagram.

4. Steam undergoes an adiabatic expansion in a piston-cylinder assembly from 100 bar, 360 C to 1 bar, 160 C. What is work in kJ per kg of steam for the process? Calculate the amount of entropy produced, in kJ/K per kg of steam. What is the maximum theoretical work that could be obtained from the given initial state to the same final pressure? Show both processes on a properly labeled sketch of the T-s diagram.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fluid at 0.6 bar occupying 0.1 m° is compressed reversibly to a pressure of 11.1 bar and specific volume of 0.4 m/kg according to the law pv =c. The fluid then expands reversibly according to the law pv = c to 2.1 bar. A reversible cooling at constant volume then restores the fluid back to initial state. Calculate the value of n in the procesS.
A piston'eylinder has two chambers and ineludes a spring, as illustrated below. The right side contains air at 318.15 K and 2 bar, while the left side is a spring in a vacuum. The spring exerts a force to the right of 5500x (SI units), where x is initially 0.3 m away from the right side of the wall (x = 0 is the position where the spring is fully relaxed). The piston has a cross-sectional area of 0.1 m?. Assume that the piston and cylinder are both well insulated. When the red stop is removed, the piston moves smoothly to a final state. What is the final position of the piston and the final temperature of the air? You may assume that air has a constant hcat capacity of c,m - 3.5R. Note: you should take the positive x direction as going to the left on the diagram. spring air vacuum
Water initially a saturated liquid at 110°C is contained within a piston-cylinder assembly. The water undergoes a process to the corresponding saturated vapor state, during which the piston moves freely in the cylinder. There is no heat transfer with the surroundings. If the change of state is brought about by the action of a paddle wheel, determine the amount of entropy produced per unit mass, in kJ/kg K. Select one: a. 5.8202 O b. 2.1968 С. 3.7721 d. 4.9961
Q1: An air receiver contains air at 16 bar and 42°C. A valve is opened and some air is allowed to blow out to atmosphere. The pressure of the air in the receiver drops rapidly to 12 bar when the valve is then closed. Assuming that the mass in the receiver undergoes a reversible adiabatic process, calculate the initial and final mass of air if you know that the amount of air which has left the receiver is 18.04 kgs.
The rate of entropy transfer associated with heat transfer from a closed system operating at steady state to its surroundings must be equal to the rate of entropy production due to irreversibilities within the system. O True O False eTextbook and Media Save for Later
Thermodynamics
A vessel of volume 0.04 m3 contains a mixture of saturated water and steam at a temperatureof 250°C. The mass of the liquid present is 9 kg. Find the pressure, mass, specific volume,enthalpy, entropy and internal energy.
1. As shown in figure A, R=0.287 kJ/kg K and k=1.4. If the ideal gas in the cylinder is heated to final state of 0.5 m3 and 800 kPa, Spring initially F=0 determine: a. Total work done by the ideal gas ANS b. The work done against the spring Frictionless Piston Pi = 200 kPa Vi=0.2 m ANS Fig. A
A fluid at 0.8 bar occupying 0.06 m3 is compressed reversibly to a pressure of 10.9 bar and specific volume of 0.5 m3/kg according to the law pvn = c. The fluid then expands reversibly according to the law pv2 = c to 2.8 bar. A reversible cooling at constant volume then restores the fluid back to initial state. Calculate the mass of fluid present.
pls correct the given this is my last attempt
Need final ans only fast please
A closed, rigid tank contains 4 kg of air initially at 300 K, 1 bar. As illustrated in the figure below, the tank is in contact with a thermal reservoir at 600 K and heat transfer occurs at the boundary where the temperature is 600 K. A stirring rod transfers W = -480 kJ of energy as shown in the diagram.The final temperature is 600 K. The air can be modeled as an ideal gas with cν = 0.733 kJ/kg · K and kinetic and potential energy effects are negligible.