4. Now consider the figure below showing a wooden block subjected to biaxial loading, and its stress state inthe laboratory coordinate system. The grain in the wood is aligned at an angle of 15° to the vertical direction asshown. Determine the stress state in the orientation of the grain.Yσy = 1.8 MPa15°σx = 3 MPaох==

Answered: Image /qna-images/answer/36800768-f454-4ab3-ba42-d82caedb6d08.jpg

Answered: 4. Now consider the figure below…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.26P: - 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v...

See similar textbooks

Similar questions

At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
In a volume element with dimensions dx, dy, dz the negatíve y-face has a 2 MPa stress in the positivex-direction, a 3 MPa stress in the negative z-direction, and a 4 MPa stress in the negatíve y-direction. Which of the following describes the stresses per elasticity convention? Oyy = 4 MPa Oyr = -2 MPa 3 MPa A MPa
Find the interal normal stress in all relevant segments of the bar in the picture.
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
Question 3 Determine the elongation of the square hollow bar when it is subjected to the axial force P = 100 kN, find the permanent elongation of the bar. The bar is made of a metal alloy having a stress-strain diagram which can be approximated as shown. o (MPa) 500 600 mm P 50 mm 250 5 mm e (mm/mm) 0.00125 0.05 50 mm ´5 mm a. Find the stress (MPa) of the bar. b. Find the permanent elongation (mm) of the bar.
solve first one only and use b h and x to find the strain
At a point on the surface of a pressurized cylinder, the material element is subjected to stresses; σx = 60 MPa, σy = - 40 MPa, and τxy = - 30 MPa. Construct Mohr’s circle, then use it to determine the following: Do not use the equations of transformations.1- The principal stresses and the maximum shear stress.2- Show these stresses on sketches of properly stress elements.3- A point on the circle where the element is only subjected to pure shear stress. Calculate the value of that pure shear stress.
Mechanics of material
please help answer and explain
An element of material is deformed as depicted in the figure. Assuming that the modulus of rigidity....
At a point in the cross-section of an engineering component an element is subject to the following stresses: σx =100MPa σy =45MPa τxy = -50MPa Construct a Mohr’s Stress Circle and hence determine: (a) The Principal Stresses (σ1 & σ2) and the Directions of the Principal Planes (φ1 & φ2) (b) The Maximum Shear Stress (τmax) (c) Find the Normal Stress (σn) acting on a plane at 40 degs anticlockwise from the y-axis
Please help me answer this thank you

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS