4. Is this current amplifier or voltage amplifier? Explain your reasons and show amplifier gain. 5. What is the limit of this amplifier? Explain your reasons using small signal condition.

Q: Instruction [25-0 Jump address (31-0 Shift left 2 26 28 PC+4 (31-28 ALU Aod (Shi R RegDst Jump…

A: The correct option is 48 Option (C)

Q: If the four input lines of a multiplexer are DO, D1, D2 and D3, and the two select lines are given…

A: Four input lines of a multiplexer, and input for the select lines are 11 then find the output of…

Q: Question 2 : al khat are the differences between logical and Continuous Sensors. b) Name two logical…

A: a) The main differences between logical and continuous sensors lie in the type of data they provide…

Q: Once the keyboard controller determines that a key has been pressed, the next step it takes is to

A: Find the explanation below

Q: please dont use AI, it gives wrong answer thank u. solve by hand and i will like

A: Question i. a. If the ARM processor is configured as little-endian, it means that the least…

Q: Identify the component which is not available in digital Voltmeter? a. Clock generator b. ADC c.…

A: We need to select component which is not inside the digital voltmeter .

Q: For your overhead water tank you have to make a system that detects the water level in the tank…

A: Finite state machines have finite number of states. Based on input and current state machine will…

Q: If the four output lines of a demultiplexer are YO, Y1, Y2 and Y3, and the two select lines are…

A: In this question , we will write output selected  for select lines 1 1...

Q: Choose the correct instruction that will read data in from an I/0 device. IN AL, 60 IN 60, AL OUT…

A: In an I/O device the command "IN" represents the input command Here IN AL,60 means that move a…

Q: Question 1: Define the following expression al Sequential Control bistate c) PLC d) GRAFCET Question…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: One latch can store bits of data. O a. one O b. infinite O c. many O d. two

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Question 3 What is the output f of this multiplexer when W1 = 0 and W2=0? W2 0 W3 1 O A.0 OB. 1 C.W2…

A: The given multiplexer diagram is shown below,

Q: Problem #3: board has three clocks that can be seen in the table below: Table 3-2 Pin Assignment of…

A: Let the input clock signal is 10MHz, ADC_CLK_10 clock signal. Which is provided to the LPM counter.…

Q: when using lm393, is it necessary to use a pull up resistor between the output and the power supply?

A: It is asked to discuss why we need to use a pull up resistor between the output and the power…

Q: How many select lines are required for a 1-to-8 demultiplexer? Select one: a. 4 b. 3 Cc. 2 d. 5

A: Given data, Select lines requires in 1-to-8 demultiplexer.

Q: PAL consists of O a. a programmable array of AND gates followed by a fixed array of OR gates O b. a…

A: PAL is programmable Array logic in which AND gates are programmable and OR gates are fixed…

Q: If the four output lines of a demultiplexer ar YO, Y1, Y2 and Y3, and the two select lines a given…

A:

Q: Which is correct in case of Computer controlled system?

A: Given Data:There are 4 statements regarding computer-controlled systems.Required Data:Here, we need…

Q: Power electronic controllers have OLow overhead capacity OHigh overhead capacity ONo overhead…

A: In this question we need to choose a correct option

Q: "What is the result of executing the following instruction sequence? MOV DX, 2364H MOV BX, 1234H MOV…

A:

Q: What will this program rung do? (assume that nothing else in the program is affecting this output.)…

A: The ladder circuit is shown below:  The single pushbutton is controlling both the lights.  By…

Q: What is the device address used by the instruction OUT A4, AL?

A:

Q: If a multiplexer has 64 input lines then it needs how many select lines?

A:

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: Choose how many and determine the type of output (digital or analog) it gives and how to interface…

A: 16 channels on the ESP32 can be utilized to generate PWM signals, allowing for a maximum of 16…

Q: What kind of sensor is this type O a. magnetic O b. inductive O c. float O d. pressure

A: What type of sensor is given in the above image ? A. Magnetic  B. Inductive  C. Float  D. Pressure

Q: How many bits are needed to count up to a maximum of 63?

A: The given number is 63

Q: (3-a) Is this an analogue or digital electronic problem? Explain the difference.

A: It is a digital electronic problem

Q: the first state is 00 00 as indicated below, What will the last stated be after the last clock and…

A:

Q: Assume R1 = AA00 FF00 H and R2 = E0BB 88A0 H, which flags get affected after ADD R1, R2 instruction?…

A: This question is from "MICROPROCESSOR" under which we are studying the status of flags after the…

Q: How many analog pins are there in Arduino MINI, UNO, and MEGA respectively? Select one: a. 14, 6,…

A: Arduino: It is an electronic pavement for the usage of hardware and software.

Q: Question No. 1: Summarize the following (two to three lines) a) Difference between precision and…

A: we need to summarize the following:a) Difference between precision and accuracy.b) Difference…

Q: Which one of the following instructions will cause a memory read when it is executed? MOV BL, AL…

A: MOV BL, AL This instruction will copy from register A to register B. Both source and destination are…

Q: Why always block is not used in Program block.

A: Wire, net type are used for continuous assignment The procedural  assignment is used to implement…

Q: actuators Question 3: a) Name two logical and two continuous actuators b) Name four techniques used…

A: a) Two logical actuators:1. Solenoid valve: A solenoid valve is an electromechanical device that…

Q: Y represents an C D B HHHHH) Instruction A E Öt O Examine If Closed instruction Examine If Open…

A: Given ladder diagram of PLC

Q: Whenever an IC is designed manufacturers use a a) Specific code and manufacturer's name b) Specific…

A: Integrated circuit designed by such electronic components like capacitors, resistors, transistors,…

Q: What is the device address used by the instruction OUT A4, AL?

A:

Q: Controlled variable is the output of O a. Error Detector O b. Controller O c. Plant O d. None of the…

A: Controlled variable is out put of