Instruction (25-0Jump address (31-0]Shiftleft 22628PC+4 (31-28ALLAodShi Rett 2RegDstJumpWBranch.MemReadMemtoRegALUOMemWreALUSCRegWriteEInstruction (31-20)ControlA 2-211ReadaddressReadregister 1Readdata 1(20-16]Instruction[31-0InstructionmemoryReadregister FReadReadAddressdatastruc(15-11Writeegister data 2RWritedata RegistersWe Datamemory MdataInstruc D(15-016ALUcontrolnstruction (-0Assume the value of St1 15 dec, and $t2- 16 dec, and Iw St0, 12($50) is executing in. What is the D wires value in decimal (as shown in the figure)?Select oneO a 16O b. 12Oc 48Od. othersOe 3Ot. 8

The correct option is 48 Option (C)

Instruction [25-0 Jump address (31-0 Shift left 2 26 28 PC+4 (31-28 ALU Aod (Shi R RegDst Jump WDranch. MemRead MemtoReg E Instruction (31-20) Control ALUOP MemWre ALUS RegWrte A 2-211 Read address Read register 1 PC Read data 1 (20-16] Read register Instruction [31-0 Read Address data Write Read Instruction memory nstruc(15-11] register data 2 Write data Registers Write Data data memory M Instruc D(15-0 16 ALU control nstruction (-0 Assume the value of St1 15 dec, and $t2 16 dec, and Iw St0, 12($50) is executing in. What is the D wires value in decimal (as shown in the figure)? Select one: O a 16 O b. 12 Oc 48 Od. others Oe 3 Ot. 8

Instruction [25-0 Jump address (31-0 Shift left 2 26 28 PC+4 (31-28 ALU Aod (Shi R RegDst Jump WDranch. MemRead MemtoReg E Instruction (31-20) Control ALUOP MemWre ALUS RegWrte A 2-211 Read address Read register 1 PC Read data 1 (20-16] Read register Instruction [31-0 Read Address data Write Read Instruction memory nstruc(15-11] register data 2 Write data Registers Write Data data memory M Instruc D(15-0 16 ALU control nstruction (-0 Assume the value of St1 15 dec, and $t2 16 dec, and Iw St0, 12($50) is executing in. What is the D wires value in decimal (as shown in the figure)? Select one: O a 16 O b. 12 Oc 48 Od. others Oe 3 Ot. 8

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q 2
Please answer the question
Microcontroller type PIC speed O a. moderate O b. non of the above Oc. slow Od. Fast
LES CX, [BX] – this instruction copies. successive words from memory pointed by BX register. O a. Two O b. One O c. Four O d. Three
There exists one or more discrete ime signal. What is it control system ? (a) discrete time or (b) continuous time
What’s the difference between Moore and Mealy machines (FSM)? Design an FSM for the following sequential adder.
Question I. Synchronous Sequential Circuit hint) W issynchronized with C C Clock pulses), output z will he comel each time the value of the input signal w had not changed for 2 dak pulses . Out put value Change will appear at the clak Pul se with identical w values. Refer below. W: 00ll000ll011100 11|1II 0000 10110... Z: ool o10 100 100 100 1010000010000l... a. Circaits State table? b. State diagram? C. Use the birany Code to encode the State and set up the encoded State table. d. obtain minimnzed expresio ns for He next State and the output fanction .
SV What is clocking block ? what is program block?
Controlled variable is the output of a. Error Detector O b. Controller O c. Plant O d. None of the above
Can you determine the difference between the various shift register types?
Figure 1 shows a block diagram of the 8051 microcontroller. Briefly describe thefunction of each of the numbered elements in the diagram as well as the T0, EA,RST, ALE, PSEN, and INT0 input/output pins.
You want the instruction OUT AL, 25 to activate the LS373 latch. Which control signal on our MCS should be connected to the Y input? LS373 A7 G A0 Y IO/M* IORD IOWR RD WR