Question 2 please Question 2 :at klhat are the differences between logical and ContinuousSensors.b) Name two logical and two continuous sensorsc) that are the difference between logical and continuousactuatorsQuestion 3:a) Name two logical and two continuous actuatorsb) Name four techniques used to describe sequential controlsystemc) Represent the general architecture of a phc and namethe various parts.Question 4:al Give four main characteristics atb1 Give four main programming languages of a PLCcl Give the name of the PLC. used in your Lab fora PLC

a) The main differences between logical and continuous sensors lie in the type of data they provide…

Answered: Question 2 : al khat are the…

Question 2 : al khat are the differences between logical and Continuous Sensors. b) Name two logical and two continuous sensors c) that are the difference between logical and Continuous actuators

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit given, If V=44 V, R1= 24 ohms, R2 = 16 ohms, R3 = 16 ohms. Voltage drop across 16 ohms resistor is,_________. See the Pic
answer question 1.d… please answer it quickly (in one hour)
1%M l1. O 10:YV Final exam Lab (pa... moodle1.du,edu.om Question U Not yet answered Marked out of 3.00 P Flag question A resistor has the following colours: green (First band), blue (second band) and yellow (third band), (Fourth band is not included in this question). The value of the resistance is Select one: a. 560 000 Ohm b. None of the above c. 22 000 Ohm Previous page Next page L Toct 1 II > II
5. What is the minimum size of rigid metal conduit? a. 3/8 inch trade size b. b. ¾ inch trade size c. c. ¼ inch trade size d. d. ½ inch trade size
first off solution is completely incorrect. the correct answer is -2vRA0 and as i said DO NOT RE-SOVLE THE QUESTION BUT JUST ANSWER THE INQUIRIES I HAVE IN THE DESCRIPTION OF THE QUESTION.
Moving to another question will save this response. Quèstion 2 The three simplest gates are AND gate, OR gate, NOT gate AND gate, NOR gate, NOT gate NAND gate, OR gate, NOT gate AND gate, OR gate, NOR gate Winciows la
I need to solve question number 4
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Convert 214 ºF to engineering notation using the appropriate SI unit. (You must provide an answer before moving to the next part.) 214 ºF in SI unit using the proper engineering notation is written as K.
The hole on the drawing below is required to be perpendicular to the bottom surface and centrally located on the plate regardless of the size of the feature and regardless of the sizes of the datum features. In order of precedence, which datum features are missing in the feature control frame? (select all correct answers) Ø2.505 -2.510 0.005 E C A B Odatums A, D, E Odatums A, D Odatum A O datums D, E, A O datums A, E, D 1 I 6.00 4.00 1.00
twwt tov + 202 VAB 2A Question #1: In less than three sentences, describe how you will solve this problem. A good answer can be as few as 6 or 7 words. www
14] Encode Decimal '-124' using Two's Complement. Express your answer in Hex. 15] How much Current is passing through a 470 ohm Resistor that is dropping 3.3 Volts? Express your answer in Decimal with 2 digits of significance. 16] How many Volts are being dropped by a 2.7k Ohm Resistor if it is passing 75uA? Express your answer in Decimal with 2 digits of significance.