4. Five separate measurements were made of a line and theirdegrees of precision computed as follows: 1" trial; 1/5000,2d trial, 1/2500; 3“, 1/6500; 4", 1/7000; 5", 1/10000. Themeasurement which is of a higher degree of precision wasthe one done in thea. 1* trialb. 2d trialc. 3d triald. 4 triale. 5" trial

Answered: Image /qna-images/answer/ab905f45-065e-415e-81ed-5c4b1378e58f.jpg

4. Five separate measurements were made of a line and their degrees of precision computed as follows: 1" trial; 1/5000, 2 trial, 1/2500; 3“, 1/6500; 4", 1/7000; 5", 1/10000. The measurement which is of a higher degree of precision was the one done in the a. 1* trial b. 2 trial c. 3" trial d. 4 trial e. 5" trial

4. Five separate measurements were made of a line and their degrees of precision computed as follows: 1" trial; 1/5000, 2 trial, 1/2500; 3“, 1/6500; 4", 1/7000; 5", 1/10000. The measurement which is of a higher degree of precision was the one done in the a. 1* trial b. 2 trial c. 3" trial d. 4 trial e. 5" trial

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DE- determination of integrating factors
ANSWER ONLY LETTER D FOLLOW THE INSTRUCTIONS TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS
A steel tape standardized at 25degree celsius and supported throughout under a tension of 73N was found to be 30.004m long. The tape had a cross sectional area of 5mm^2 and a weigh of 45g/m. This tape was used supported at the ends only with a constant tension of 75N to measure a line from A to B in nine segments. The data given in table 1 were recorded. Apply correction for tape, length, temperature, pull,sag and tape not horizontal to determine the correct length of the line Table 1. Recorded data for nine segments measurements Measured Temperature ("C) Difference in Elevation (m) Section (Recorded Distance, m) А-1 30 15 0.384 1-2 30 15 0.293 2-3 30 16 0.183 3-4 30 16 0.247 4-5 30 16 0.372 5-6 30 17 0.628 6-7 30 17 0.774 7-8 30 17 0.817 15.73 8-B 18 0.570
how to get the percentage error
can u help Write a brief conclusion on the answer that you obtain from the above question. Is it liable and okay to obtain this amount of error? Explain your point of view.
A steel tape standardized at 20degree celcius and supported through out under tension of 90N Was found to be 30.377m long. The tape had a cross sectional area of 55mm^2 and a weight of 73g/m. This tape was used supported at the ends only with a constant tension of 78N to measure a line from A to B in nine segments. The data given in the following table were recorded. Apply correction for tape, length,temperature,pull,sag and tape not horizontal to determine the correct length of the line Difference in Elevation Cm) 0-392 Section Meacured Recarded Distance) Tempergrare A-1 15 1- 2 30 15 0.301 2-3 30 16 O.191 3-4 16 0-255 4-5 30 16 0-38 5-6 30 8.636 6-7 0.782 7-6 30 0-825 8-8 25.348 18 0.578 Sum = 265-348 m
determine the value of W
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
Help
With your pencil, make a dot on the position of your best visual estimate of the centroid of the triangular area. 14.0 11.2 8.4 5.6 2.8 0 4.8 Now refer to Sample Problem 5/2 and to Table D/3 and find the exact location of the centroid. 0 (x, y) = (i 1.6 3.2 How close did you come with your guess? 6.4 8.0