4. Explain the difference between the following pairs: a. Strain and stress b. Homogeneous and heterogeneous strain c. Longitudinal strain and shear strain d. Infinitesimal strain and finite strain

Q: Material A has a modulus of elasticity between Materials B and C, where the value of Material B is…

A: Given : Material A between B and C B is highest D is lowest Strain in A and B is same Strength B and…

Q: What is the transformation of strain at a point?

A: The strain transformation at a point occurs only when the stress acting on the material is plane…

Q: 3. Two specimens with the same dimensions and made from two different materials, A and B, were…

A:

Q: V Use the engincering stress strain diagram provided below to answer parts (A) to (1) below (the…

A:

Q: A 40 mm diameter rod of a certain material is 1,2 m long and has a collar fitted to one end. The rod…

A: Diameter is 40 mmLength is 1.2 mWeight Extension Maximum stress in bar

Q: Which of the following is an accurate statement? (A) The lateral strain is greater than the axial…

A: Axial strain :-The change in length over the original length of a material along its axis is…

Q: The state of strain at a point is characterized by six strain components,Name them?

A: The state of strain at a point can be represented by strain tensor which is used to define different…

Q: Can the Mohr’s circle be used to determine the principal strains, the maximum strains, the maximum…

A: Mohr's circle is a graphical method to find the principal stresses and strains of the material.

Q: 1. A tensile test was conducted on a metal "505" specimen and the following stress-strain curves…

A: Elastic Modulus (Young's Modulus): The elastic modulus represents the stiffness of a material and is…

Q: When an element of material is subjected to deformations that only occur in a single plane, it…

A: If the state of  strain acting on a material particle is such that the non-zero strain components…

Q: A UTS with a machine stiffness of 75 KN/mm is used to measure load/displacement points in the…

A:

Q: If the area under the stress and strain curve is more then it is concluded that the material has…

A: The area under stress - strain curve represents the energy required or stored in the material before…

Q: The relationship between true strain (ɛ-) and engineering strain (ɛ) in a uniaxial tension test is…

A: Given:Engineering strain=εETrue strain=εT

Q: tion 2 2. A cord has original length of 100 cm is pulled by a force. The change in length of the…

A: According to the strain definition, it is defined as the amount of deformation experienced by the…

Q: The general equation that describes the relationship between the stress and the strain for ductile…

A: Correct answer: 3. Hooke's law

Q: A homogenous 900 kg bar AB is supported at either end by a cable as shown. Calculate the following:…

A:

Q: In the force measurement experiment, the weight of the strain is increasing order and at intervals…

A: An electrical sensor with the help of which the force or the strain applied on any object can be…

Q: (2) luhai The difference between shear strain and linear strain

A:

Q: State your answers to the following questions. Strain Gauge represents the deformation of a material…

A: Explanation Strain gauges works on the principle that the change in dimensions  of the material…

Q: You need the shear modulus for a particular material in order to calculate shear strain for a known…

A:

Q: ase calculate the strain and stress in the following two prompts a. A 1 cm long section of tendon…

A: This question is based on the concept of stress and strain

Q: When a homogeneous isotropic material is subjected to a state oftriaxial stress, the strain in each…

A: In a homogeneous material, all the properties are the same at each and every point of the material.…

Q: Poisson's ratio is defined as

A: Given data : Lateral strain is denoted by εLT Longitudinal strain is denoted by εL   Required :…

Q: Derive the expression for the strain transformation.

A: Strain transformation:-  Strain-Transformation equations are based on the geometry of the…

Q: OA =240 MPå raw the T and M diagrams. alculate the force Pa that will start flowing in the beam.…

A: Givenyield stress σy=240MPa

Q: A single strain gauge is mounted to measure the axial strain in a simple tensile member the recorded…

A: Data given -  Strain € = 200 × 10-6  Esteel = 200 GPa = 200 × 109 N/m2 Ealuminium = 70 GPa = 70×109…

Q: To draw the shear stress-strain diagram, the collected data needed are the force applied on the…

A: The given statement is true.

Q: Under which of the conditions below is the generalized Hooke’s law applicable for use in analysis?…

A:

Q: A single strain gauge is mounted to measure the axial strain in a simple tensile member the recorded…

A:

Q: Hooke's law is used to correlate true stress and true strain in the plastic region of the…

A: Described Hooke's law is used to correlate true stress and true strain in the plastic region of the…

Q: Is the direction of the positive principal strain defined by the counterclockwise?

A: The shear stress is considered as the positive when the pair of shear stresses acting on the…

Q: What is the Linear Normal-Strain Distribution?

A: Linear Normal Distribution is defined as the distribution of  normal strain linearly. Linear…

Q: QUESTION 7 Which governing equations are required to solve a plane elasticity problem? Boundary…

A:

Q: The ratio between lateral strain and longitudinal strain is known as Poisson's ratio      Select…

A: Longitudinal strain is the strain produced in the direction of the applied load, while lateral…