A single strain gauge is mounted to measure the axial strain in a simple tensile member the recorded strain is 200 microstrain, what is the axial stress ?  a) If the member is of steel? b) if the member is of aluminium ? The modulus of elasticity of steel is 200 GPa and that of aluminium is 70 GPa

Q: A mild steel specimen of Diameter 9 mm, Length 11 cm is subjected to tensile load and it is found…

A: Given Data Diameter of specimen is : d=9 mm Length of specimen is : L=11 cm=110 mm Modulus of…

Q: d) If a material of a component has a youngs modulus of elasticity of 800 GPa, what strain will be…

A: Given data: E=800 GPaσ=5 MPa Need to determine the strain.

Q: he following data are obtained from a tensile test of a copper specimen. The load at the yield point…

A:

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: For the truss in figure below, the cross-sectional area of the truss members isA = 500 mm²…

Q: If a specimen percentage elongation is observed to be 30%. The original length of the specimen is 10…

A: Given data: L0=10 cmpercentage elongation = 30% Need to determine the final length of the specimen.…

Q: Which of the following stress strain curve shows an elastic behaviour to very high strain rate a.…

A: The rate of the elastic behavior of any material can be calculate the slope of the stress-strain…

Q: for a clear solution

A: As per Bartleby policy if multiple questions asked then only first 3 parts need to solve hope you…

Q: A strain gauge has a resistance of 100 Q is connected as a one arm of a whetstone bridge to measure…

A:

Q: The following data are obtained from a tensile test of a coppe - The load at the yield point is 151…

A:

Q: What is the unit of strain?

A:

Q: 2- A piece of muscle specimen has the initial length of 30mm and square cross section with original…

A: Stress : Stress is the force applied to a material, divided by the material's cross-sectional area.…

Q: Problem 1: Warm-ups a) Four strain gauges are bonded to a cylindrical bar as shown below. What…

A:

Q: A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

A:

Q: A) Steel Alloy rod made of Stainless Steel 304 is subjected to 60 kip of Tensile force. Steel rod is…

A: Dear student, as per the guidelines, we are suppose to solve only one question. Please post other…

Q: A strain gauges system mounted at a point on a structural member that is subjected to multiaxial…

A: Given data, Normal strain in x-direction, εx=6.686×10-4 Normal strain in y-direction, εy=3×10-4…

Q: In the homogenous strain region of a tensile test, a sample elongation of Al=10 mm is measured. The…

A: As per our guidelines, we can answer only the first three parts. Kindly post the remaining questions…

Q: Pls answer thank you! A circular rod is 128 mm in diameter and carries gauge marks placed 50.8 mm…

A:

Q: sce M13.5 Strain measurement with rosettes Ea 500 µE Eb -200 με %3D Ec 250 με 30° 30° I| ||

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: In the force measurement experiment, the weight of the strain is increasing order and at intervals…

A: An electrical sensor with the help of which the force or the strain applied on any object can be…

Q: When force P is apliced to the rigid arm BC, point B moves downward 0.2mm. Determine the normal…

A:

Q: We're measuring axial load in a rectangular bar with two strain gauges: one on the top in the axial…

A:

Q: e maximum allowable load

A: To find Maximum allowed load

Q: The ratio of the strain in the lateral direction to that in the axial direction A Pascal's Number…

A: Given data Strain is the ratio of change in dimension to original dimension.

Q: material have a stress strain curve which can look similar to the equation y = x2 (for all x>0).…

A: Given Data⇒Stress strain curvey=x2Problem definition⇒Problem says choose between true and false.

Q: An electrical-resistance strain gage records a strain of 400 µm/m on a steel tension member. What is…

A:

Q: 1. Calculate the strain in a 42 in. long copper wire that stretches 0.035 in. [unitless, decimal…

A: The given data  Original length of wire lo= 42 in  The stretch in wire (lf -lo) = 0.035 in  Find the…

Q: What is the approximate yield stress of the material shown Stress-Strain Curve 800 700 600 500 400…

A: Option b is correct.

Q: 0.09. Assuming that a A metal has a strength coefficient K = 210,000 psi and n tensile-test specimen…

A: find true UTS Detailed calculation is provided in solution part

Q: The inspection of some aircraft components revealed the presence of 4 cracks. The table below…

A: The expression for the strength of crack is given by, σ=kYπa   For crack A,…

Q: In a tensile test for an aluminum alloy, the sample is 2 inches long and 0.5 inches in diameter. The…

A:

Q: What is the modulus of elasticity if stress is 300 Mpa and strain of 0.00138? a. 217.39 x 103 Mpa…

A:

Q: The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter…

A: To find: The modulus of elasticity and plot the stress and strain diagram. Given: Table for load and…

Q: A cylindrical aluminum alloy 10 mm in diameter and 70 mm long is pulled in tension with a force of…

A: Answer: (a) The specimen elongation is 0.21 mm. (b) The reduction in specimen diameter is 0.0099 mm.…

Q: ) What do you mean by strain? A strain gauge has a resistance of 157.4 ohms and a gauge factor of…

A:

Q: Based upon the information in the table below, which material is the stiffest? Fracture Strength…

A: Stiffness: When the load is applied on any object or material than it deform. The stiffness of any…

Q: Question 2 In designing prosthetic sockets, the latter will need to be experimentally tested for…

A: Given: The strain along gauge a, εa = 2500x10-6 The strain along gauge b, εb = 1500x10-6 The strain…

Q: 1. By using the simply tension test and the strain energy to prove the Young Modulus E is positive.…

A: Given: The strain gradient matric,

Q: Part D-Permanent elongation of the specimen if the specimen is loaded until its nominal stress value…

A: Givenσ=65ksiε=0.06

Q: As a result of the tension applied from the base in the X axis, the strain value of the structure in…

A: Given:  H= 8 cm L= 4cm α = 50° t= 5 mm νzx=- sin2αcos αHL-cosα εx = 0.26 mm/mm

Q: Ql- i mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram…

A: Given-Data:- Diameter(D)=20 mm Length(L)=40 mm Final Diameter(D)=18 mm Final Length (L)=45mm…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.