Under which of the conditions below is the generalized Hooke’s law applicable for use in analysis? a. When the material distorts due to any of the normal stresses b. When the material has a negative value for Poisson’s ratio c. When the material exceeds its proportional limit but still remains elastic d. When the material’s cross-section changes along one direction

Q: What is the relationship between the ?distance from neutral axis and stress

A: The stress, s, in the element a distance, y, from the neutral axis i s proportional to the…

Q: Consider steel B is a cylindrical sample with original length 40mm and subjected to 15700N.…

A: Option b is correct.

Q: True strain is based upon (A) Original c/s area (B) Final c/s area (C) Average c/s area (D)…

A: In the case of engineering stress and strain curve , the curve is dependent upon the gauge length of…

Q: Which one is the correct answer please?

A:

Q: 3. The state of stress at a point in a continuum body is given by X 1.5 0 1.0 0 00 [a] 1.5 0 MPa…

A:

Q: Part A The rectangular plate undergoes a deformation shown by the dashed lines where D = 4 in. dj =7…

A:

Q: 7. The fatigue crack growth data as shown in the table are obtained under the air environment of the…

A: Given data: R = -1 σmax=200 MPa Find: (a) Draw a-N curve  (b) Draw Iog(da/dN)-log(∆K)curve, and…

Q: Select all answers that are correct. Which of the following statements explain why solids have…

A: The atoms of the solid are rigidly bounded and allowed only vibrate within its own small ranges but…

Q: When a material is subjected to repeated stresses it will not fail without any prior indications.

A: When we apply repeated load on a material, then the properties or strength of the material will…

Q: It relates the displacement of the structure so that its various parts fit together a. Equilibrium…

A: Hello dear As you have posted multiple question at a time and According to our guidelines I can…

Q: n ductile materials occurs when the stresses at the crack tip ation factors for ductile materials…

A: a) factor of safety is always used while designing a components ( True)  b) small radius of…

Q: Which one(s) of the following about G, shear modulus of elasticity of a material are correct? select…

A:

Q: When an element of material is subjected to deformations that only occur in a single plane, it…

A: If the state of  strain acting on a material particle is such that the non-zero strain components…

Q: Three identical fatigue specimen ( denoted A ,B and C ) are fabricated from none ferrous alloy .Each…

A: Given: Specimen max. stress(MPa) min. stress(MPa) A +450 -150 B +300 -300 C +500 -200

Q: A two-layered material is made of two metal bars, each with square cross-sectional area t² and…

A: Given: Thickness of each bar is t Increase in the temperature=∆T Let the coefficient of thermal…

Q: Please select the correct answers according to the given figure for the elastic behaviour of steel…

A:

Q: Please match different stresses to the stress value corresponding to the different points on the…

A:

Q: In stress and strain diagram for a perfectly ductile material, the yield strength, and ultimate…

A: Ductile Materials  have  the ability to elongate in tension. Ductile material will deform (elongate)…

Q: If we want to measure the stress of a flat non-uniform component, what should we pay attention to…

A:

Q: 3. A steel tape is calibrated at 20°C. On a cold day when the temperature is -15°C,what will be the…

A:

Q: following comparisons is always true?

A: Given: GA=2GB Same poisson's  ratio and yield shear stress for A and B

Q: sce M13.5 Strain measurement with rosettes Ea 500 µE Eb -200 με %3D Ec 250 με 30° 30° I| ||

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A property of a material if, after being loaded, the material returns to its original shape when the…

A:

Q: Which Failure Theory(ies) is(are) used for a Ductile Material under Cyclic Loading?

A: Ductile Material:A ductile material is a type of material that exhibits plastic deformation before…

Q: If a material had a modulus of elasticity of 2.1 × 106 kgf/cm² and a modulus of rigidity of 0.8 ×…

A:

Q: 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 0.95 1 1.05 1.1…

A:

Q: A square cross-section v-notched specimen of height 75 mm has each side of 10 mm has been selected…

A: Given data  Height of specimen (h) = 75 mm side length (a) = 10 mm  cross section area at notch…

Q: A titanium alloy (Ti-5Al-2.5Sn) specimen with the dimensions shown below is subjected to a uniaxial…

A: The stress of a bar is given by,  , where P is the normal load and A is the cross-section area of…

Q: Based upon the information in the table below, which material is the stiffest? Fracture Strength…

A: Stiffness: When the load is applied on any object or material than it deform. The stiffness of any…

Q: (B); Consider the instrument of Electrical Resistance Strain Gage shown in the Figure 2, and answer…

A: Passive or Active Transducer: An Electrical Resistance Strain Gage is a passive transducer. A…

Q: Modulus of rigidity is defined as the:

A: Modulus of rigidity is also known as shear modulus which is the property of material which accounts…

Q: For ductile and linearly elastic material, stress is directly proportional to strain a. Below or at…

A: 1.Option (a) Below or at the yield point only. Is correct option Explanation: Stress is directly…

Q: Which one of the folowing is not correct ?

A: Given; The maximum shear stress theory predicts that shear yieldvalue ζy is 0.5 times the tensile…

Q: Which sketch correctly shows the safe region for the Distortion Energy Failure Theory? (a) (b) (c)…

A: Distortion energy theorem is also known as maximum shear strain energy theorem and it is given by…

Q: Which of the following statement is correct? (a) The stress is the pressure per unit area. (b)…

A: Option d is correct: Stress is directly proportional to strain within elastic limit.

Q: For the stress-strain curve shown below, please estimate the properties indicated. Please do your…

A: Given:Stress-Strain curve.To find:Various mechanical properties enlisted.

Q: If the Young’s modulus and rigidity modulus of a material are 210GPa and 70GPa respectively,…

A: We have given the following problem If the Young’s modulus and rigidity modulus of a material are…