4. A wall with an area of 10 m? is made of a 2 cm thickness of white pine (k=0.113 W/-deg C) followed by 10 cm of brick (k=0.649 W/m-deg C). The pine is on the inside where the temperature is 30 deg C while the outside temperature is 10 deg C. Assuming equilibrium conditions exist, what is the temperature at the interface between the two metals

4. A wall with an area of 10 m? is made of a 2 cm thickness of white pine (k=0.113 W/-deg C) followed by 10 cm of brick (k=0.649 W/m-deg C). The pine is on the inside where the temperature is 30 deg C while the outside temperature is 10 deg C. Assuming equilibrium conditions exist, what is the temperature at the interface between the two metals

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 Consider a two degree of freedom bar elements as shown in figure. Using finite element method to formulate the equilibrium equation of it. If the cross sectional area is 12 mm and E=200 GN/m2. 12 20KN 30KN 1SKN 300 600*350 bom All Dimensioon in num
At a temperature of 21.4°C the hole in a steel plate has an area of 8.80 x 10- m2. You heat the plate until the area of the hole increases to 8.97 x 10- m2, which allows a steel rod to just slip through this hole. What is the final temperature of the plate? The coefficient of linear expansion of steel is 12 × 10-0/°C.
Q2 Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer.
i need the answer quickly
A thin tube of uniform thickness 5 mm and square cross section, shown below, is subject to a torque of 1500 N·m. The shear modulus of the material is 80 GPa. What will be the angle of twist per length (in unit: rad/m)? 50 mm 50 mm
A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the other end is at x = 3. The thermal diffusivity of the bar is k = 0.4. The bar's initial temperature f(x) = 300 degrees Celsius. The ends of the bar (x = 0 and x = 3) are then put in an icy bath and kept at a constant O degrees C. Let u(x, t) be the temperature in the bar at x at timet, with t measured in seconds. Find u(x, t) and then u7 (2, 0.1). Put uz (2, 0.1) calculated accurately to the nearest thousandth (3 decimal places) in the answer box.
A brass plug is to be placed in a ring made of iron. At 20°C, the diameter of the plug is 8.755 cm and that of the inside of the ring is 8.741 cm. They must both be brought to what common temperature in order to fit? Given : Required : Illustration: Solution: final answer:
A furnace wall is to be designed to transmit a maximum heat flux of 220 Btu/hr.ft of wall area. The inside and outside wall temperatures are to be 2200 • F and 320 ° F. Determine the most economical arrangement of bricks measuring (9 in x 4; in x 3 in). If they are made from materials one with ak of 0.44 Btu/hr. ft. ° F and maximum usable temperature of 1700 ° F and other with a k of 0.94 Btu/hr. ft. ° F and a maximum usable temperature of 2400 ° F. Bricks made of each material cost the same amount and may be laid in any manner (but bricks must remain intact, i.e., no partial bricks). After you answer the question, determine the percent increase in heat flux if there are two -in.-diameter steel bolts extending through the wall per square foot of wall are. (k of steel = 22 Btu/hr. ft. F)|
3-52 A 4-m-high and 6-m-wide wall consists of a long 18-cm X 30-cm cross section of horizontal bricks (k = 0.72 W/m . °C) separated by 3-cm-thick plaster layers (k = 0.22 W/m . °C). There are also 2-cm-thick plaster layers on each side of the wall, and a 2-cm-thick rigid foam (k = 0.026 W/m - °C) on the inner side of the wall. The indoor and the outdoor temperatures are 22°C and −4°C, and the convec- tion heat transfer coefficients on the inner and the outer sides are h₁ = 10 W/m² . °℃ and h₂ = 20 W/m². °C, respectively. Assuming one-dimensional heat transfer and disregarding radi- ation, determine the rate of heat transfer through the wall. Foam Plaster Brick 1+₂+18 2 FIGURE P3-52 18 cm N 1.5 cm 30 cm 1.5 cm
Mechanics of materials I
In the figure below, it is known that the thermal conductivity of k1 = 0.06 W/mK, k3 = 0.04 W/mK, and k4 = 0.12 W/mK. The thickness of the layers is L1 = 1.50 cm, L3 = 2.8 cm, and L4 = 3.50 cm. Known temperatures T1 = 30°C, T12 = 25°C, and T4 = -10°C. Energy transfer through walls is constant. How much is T34?
Consider the following cases: Case 1: A rod with specified surface temperature. Case 2: A rod with specified surface temperature with heat generation. Case 3: A rod with specified surface temperature with variable thermal conductivity k=k(1+ßT), ß: is constant. The quadratic temperature profile T(r)= f(r ) will be in: Select one: A. Case (1) and Case (2) ONLY B. Case (1), Case (2) and Case (3) C. Case (1) ONLY D. Case (2) ONLY E. Case (3) ONLY F. Case (1) and Case (3) ONLY G. Case (2) and Case (3) ONLY