Using the Wickström equation, determine the temperature you can expect reinforced steel to be if it is in a 300mm by 300mm concrete beam and is 30mm deep in to the concrete on the heated side. The beam is being heated by the ASTM E119 aurve on one side. Find the temperature of the reinforcing steel at 1.3 hours. O 565°C O 453°C O 718°C O -298.96°C

Using the Wickström equation, determine the temperature you can expect reinforced steel to be if it is in a 300mm by 300mm concrete beam and is 30mm deep in to the concrete on the heated side. The beam is being heated by the ASTM E119 aurve on one side. Find the temperature of the reinforcing steel at 1.3 hours. O 565°C O 453°C O 718°C O -298.96°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.54-cm. steel bolt is used to clamp two aluminum (2014-T6, HT aged) plates together as shown by Fig. Problem 5. The aluminum plates have a total thickness of 5.08 cm. and an equivalent diameter of 5.08 cm. The bolt is heated to a temperature of 93.33 °C, the inserted in the aluminum plates, which are at 26.7 °C, and tightened so as to have a tensile tightening stress of 207 MPa in the unthreaded shank while steel at 93.33 °C. What is the tensile stress in the bolt after assembly has cooled to 26.7 °C? The deformations are elastic. Fe Aluminum Ports 2D- -D- Grip 2" B Steel- Fe
The assembly has the diameters and material make-up indicated. It fits securely between its fixed supports when the temperature is 7₁-70 "F Egurs.1) Figure 2014-T6 Alumi 12 CM Br 304 sel 1011 Part A Determine the average normal stress in the aluminum when the temperature reaches 75-106 "F Express your answer to three significant figures and include the appropriate units. Submit Part D HA Value X Incorrect, Try Again o Sustent Press Answers Reavest Answ Determine the average normal stress in the bronze when the temperature reaches 7) 106 "F Express your answer to three significant figures and include the appropriate units. 0? HA Units Value Units input for part A Hearst Answer Units Pearson
(b) If a steel shaft of diameter 50 mm is subjected to cooling within the steel of 80 °C, determine the diameter of hole that the shaft can be inserted into. Take the coefficient of linear expansion of steel to be 15 x 10-6 K-1.
Question 1 The exterior wall of a building consists of 100 mm thick face brick (k = 0.9 W/m-K), 40 mm thick polystyrene insulating board (k = 0.036 W/m-K), 125 mm thick concrete block (k = 1.8 W/m-K) and 15 %3D mm thick interior gypsum board (k = 0.18 W/m-K). The inside and outside convective heat transfer coefficients are 6.5 W/m2-K and 22.5 W/m2-K, respectively. The outside air temperature is -5°C and the inside air temperature is 20°C. The wall is 3 m high and 15 m long. Calculate the rate of heat loss (in W) through the wall. Round your answer to 2 decimal places. Add your answer Follow-up question to Question 1, calculate the temperature (in °C) of the interior surface of the wall. Round your answer to 2 decimal places. Add your answer Follow-up question to Question 1, calculate the temperature (in °C) of the exterior surface of the wall. Round your answer to 2 decimal places. Add your answer
Question 9. The following non-homogeneous heat equation Ut = 3uxx +π-x models the distribution of heat in a metal rod. Solve the equation if the initial temperature u(x, 0) = x, and the the boundary conditions are: u(0, t) = u(π, t) = 0.
20. The two plates of Problem 11 made of the same material and having constantk are exposed on one side to hot water at Tw and hw and on the other to cold air atTa and ha. Find a) the equation for temperature profile in these plates and b) temperaturesat x = 0 and at x = L if hw = ha = h. [Ans.: a) T1(x) = c1x + c2 where, c1 = hw(Ta – Tw)/c3 and c2 – Ta = – hw(haL +k)(Ta – Tw)/(hac3) where c3 = (k + hwL + hwk/ha)].
from my homework
Bebang owns a 830-mm-thick concrete brick table top that has an area of 10,000,000 mm^2 and a 0.750-cm-thick glass plate that has an area of 20,000 cm^2. Assuming the same temperature difference across each, what is the ratio of the rate of heat conduction through the plate with respect to the rate of heat conduction through the table top? Use Table 10.1(given below) for the value of Thermal Conductivity k. Table 10.1 Thermat Conductivities of Common Substances Values are given for temperatures near o °C. Substance Thermal Conductivity k (W/m-O Diamond 2000 Silver 420 Copper 390 Gold 318 Aluminum 220 Steel iron Steel (stainless) 14 Ice 2.2 Glass (average) 0.84 Concrete brick O.84 water 0.6 Fatty tissue (without blood) 0.2 Asbestos 0.16 Plasterboard 0.16 wood 0.08-0.16 Snow (dry) 0.10 Cork 0.042 Glass wool 0.042 wool 0.04 Down feathers 0.025 Air 0.023 Polystyrene foam 0.010
1- Microwave radiation is incident on one side of a planar wall with a heat conductivity coefficient k. (x=0) -D°b=(x)b leads to volumetric heating. While this surface is 9(W/m²) microwave radiation is fixed. kept at a constant temperature To, the other surface at x=L is very well insulated. Determine the temperature distribution T(x) in terms of x, L, k, qo and To.
What is the thermal resistance of a 3 in fired clay brick with density of 120 Ibm/ft3 a. 0.422 b. 6.8 c. 0.48 d. 6.2
In a thin-walled cylindrical pressure vessel, the axial and circumferential joint efficiencies specified to account for fabrication process and inspection procedure considerations are 1.0 and 0.5 respectively. The ratio between the circumferential stress and axial stress used in the design is, O a. 1:1 O b.4:1 Ос 1:2 O d.2:1
Using Ritz technique, determine the temperature distribution in the fin. T=20 °c, h=0.3 w/cm² °c, k=4 w/cm °c. Assume free end is open to the atmosphere