4. A round steel shaft rotates at 200 rpm while delivering 5000 W to a gear producing a bending moment of 350 N.m. Find the diameter of this shaft if the allowable shearing stress is 60 MPa and the allowable bending stress is 40 MPa..

4. A round steel shaft rotates at 200 rpm while delivering 5000 W to a gear producing a bending moment of 350 N.m. Find the diameter of this shaft if the allowable shearing stress is 60 MPa and the allowable bending stress is 40 MPa..

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: Give a complete solution, Don't use the direct formula. [1] A semicircular groove with a 5-mm radius…

Q: A solid shaft with a yield strength of 500 MPa subjected to a torque of 60N.m and bending moment of…

A: Step 1: Given data:Yield strength, σy=500MPaTorque, T=60N.mBending moment, M=70N.mStep 2: We need…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

Q: For the cross-section shown below, computer the rate of twist and the shear stress if a torque of…

A: Torsion Torsion is a twisting of object when torque is applied on it. Torque Torque is a…

Q: A certain circular shaft is subjected to a maximum equivalent bending moment of 36,000 in-lb and a…

Q: A mild steel shaft of 50mm diameter is subjected to a bending moment of 1.9kNm. If the yield point…

A: Introduction The maximum shear stress hypothesis states that a material will fail or yield if its…

Q: Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…

A: Given data: Power at Gear C, PC= 40kW Power at Gear B, PB=15KW Power at Gear A, PA= 40-15=25kW…

Q: A stepped shaft ABCO consisting of solid circular segments is sublected to three torques, as shown…

Q: (12) A Ø50mm shaft is 3.0m long& receives 45kW from a pulley mounted @ 2.0m form the left end. A…

A: The schematic diagram of the shaft is Given data, Diameter of the shaft, d = 50 mm Length of the…

Q: 2. The solid shaft AB has a diameter d_s = 1.5 in. and is made of steel with a shear allowa of 12…

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

4. A round steel shaft rotates at 200 rpm while delivering 5000 W to a gear
producing a bending moment of 350 N.m. Find the diameter of this shaft
if the allowable shearing stress is 60 MPa and the allowable bending
stress is 40 MPa..

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
6. A marine turbine developing 15,000 hp and it turns the shaft at 300 rpm. The propeller which is attached to the shaft develops a thrust of 150,000 lbs. A hollow steel shaft with an outside diameter of 14 in. will be used. The maximum shearing stress based on the torsion alone is not to exceed 7.5 ksi. Find the thickness of the hollow shaft in mm.
Example 3 (a) A steel transmission shaft is 510 mm long and 50 mm external diameter. For part of its length it is bored to a diameter of 25 mm and for the rest to 38 mm diameter. Find the maximum power that may be transmitted at a speed of 210 rev/min if the shear stress is not to exceed 70 MN/m’. (b) If the angle of twist in the length of 25 mm bore is equal to that in the length of 38 mm bore, find the length of the two bored parts.
A solid circular shaft is required to transmit 200 kW while turning at 90 rpm (rev/min). The allowable shearing stress is 42 MPa. Find the required shaft diameter.
I need correct solution
A hollow steel shaft 2540 mm long must transmit a torque of 34 kN-m. The total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 MPa. Find the OUTSIDE DIAMETER and INSIDE DIAMETER of the shaft that meets these conditions (in mm). Use G = 83 GPa.
The end of a 2.5 in diameter steel shaft is milled to two flats (one flat on the top and one flat at the bottom) to permit the use of a hand crank. Each flat is located 1.00 in from the center of the shaft. A torque of 750 Ib-in is applied. Find: (a) the maximum shear stress at the end of the shaft with two flats in psi unit. (b) the angle of twist in fadians (c) the angle of twist in degrees h= 1.0 in h= 1.0 in d= 2.50 in Show all your calculations.
A shaft has an external diameter (ED) of 350 mm and an internal diameter of 150 mm. i. Calculate the maximum shear stress in the shaft when it is transmitting 3700 kW at 100 rpm. ii. Find the angle of twist in a length of 20 x ED. (Assume G=75GN/m2). iii. If the hollow shaft is replaced by a solid shaft of the same weight and length, what power can it transmit for the same maximum shear stress?
A steel shaft 50 mm diameter and 500 mm long is subjected to a twisting moment of 1100 N-m, the total angle of twist being 0.6°. Find the maximum shearing stress developed in the shzaft and moduhis of rigidity. A spindle as shown in Fig. 5.34, is a part of an industrial brake and is loaded as shown Each load P is equal to 4 kN and is applied at the mid point of its bearing. Find the diameter of the spindle, if the maximum bending stress is 120 MPa. 125 mm 25 mm P. 25 mm Fig. 5.34
Please don't copy Find the torque and power transmitted by a 100 mm diameter shaft, if maximum angle of twist and length of shaft are 1.2° and 2 m. Take G = 70 GPa, speed of shaft = 230 r.p.m.