4. A delta connected balanced load is connected to a 3 – phase, 400 V supply. The line current is 35 amperes and the load power factor is 0.8 lagging. Find: a. Resistance per phase b. Reactance per phase c. Impedance per phase d. Total power e. Total reactive volt ampere

4. A delta connected balanced load is connected to a 3 – phase, 400 V supply. The line current is 35 amperes and the load power factor is 0.8 lagging. Find: a. Resistance per phase b. Reactance per phase c. Impedance per phase d. Total power e. Total reactive volt ampere

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Related questions

Q: 1. What is the main direct cause of reactive power in AC system? A. Resistance of transmission lines…

Q: 1. For each of the three single-phase transformers below, the phase pos voltage has been drawn on…

A: According to question: The phasor diagram is drawn by assuming that the turn ratio of each…

Q: Show how you can connect two single-phase transformers to obtain 3-phase output from a 2-phase power…

A: Conversion of 3 phase into 2 phase and 2 phase into 3 phase using two single phase transformers is…

Q: Three single phase loads are connected to the 400 V, three phase lines, 60 Hz. Load 1 operating at 3…

Q: (b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta-…

Q: the figure below to supply a balanced 3-phase, 150 KVA, 600 VLL load from primary 4.16 KVLL line.…

A: Please find your answer below in step 2

Q: Describe a single-phase circuit, polyphase circuit, and a three-phase circuit. List the advantages…

A: In electrical engineering, the distribution and transmission of electrical power are achieved…

Q: A three phase load is connected in delta to a three phase 440 V, 50 Hz mains. An inductor of 100 mH…

A: Solution: A three phase load is connected in delta, voltage V=440 v, f=50 Hz, Inductor L= 100mH…

Q: If you have 3-phase power and you need to step down (or up) in 3-phase voltage, how many…

A: The objective of the question is to determine the number of single-phase transformers required to…

Q: A single phase 120V AC sourc controls power to a resistve load 202 using integral cycle control. a)…

A: Note: As per our policy, I have attempted the first three subquestions. Given data: The source…

Q: In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws…

Q: Describe the concept of three-phase power in electrical systems and its advantages over single-phase…

A: In this question, we need to describe the concept of three phase power in electrical system and also…

Q: 50. A series resistance-capacitance (R-C) circuit is connected to 230-volt, 50 cycle AC source. The…

Q: . Calculate the line currents for phase a, b and c. 2. Calculate the line-to-neutral voltages at the…

A: From the given circuit Van = 120 ∠0 V V bn = 120∠-120 V V cn = 120 ∠-240 V R a=R b=R c=…

Q: The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical…

A: Given: Load-1:P1=950Wcosϕ1=0.5 LaggingLoad-2:P2=1.14Wcosϕ2=1Load-3:P3=760Wcosϕ3=0.5 leadingline…

Q: A star connected three phase alternator supplies power to a delta connected resistive load. The…

A: The figure for star-connected three-phase alternator with delta connected resistive load is:

Q: 5.In three-phase transformers, the high voltage star connection is preferred. This is so because in…

A: It is given that:In three-phase transformers, the high voltage star connection is preferred.

Q: Design a three-phase system such that the phase current in the generator, lines and charging phase…

A: Given data: Phase voltage VP=1000 V(rms) Phase current Ip=10 A(rms) Power factor = 0.97 lagging…

Q: (b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta-…

Q: Two impedances consist of resistance of (15 ohms and series connected inductance of 0.04 henry) and…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Three single phase loads are connected to the 400 V, three phase lines, 60 Hz. Load 1 operating at 3…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5 +…

Q: Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5…

A: Primary Voltage = 7900VSecondary Voltage = 7970 VLoad Impedence = 30+j40 ohms1st transformer…

Q: For reactive load, the power factor is equal to Select one: O a. 1 O b. 90 O .2 O d.0

A: GIVEN DATA:

Q: Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10…

A: In this question, 3 loads are connected in parallel then find the total current IT ? If Three…

Q: Three single phase transformers each having a 240 V primary and two 250 V secondaries, as shown in…

A: The primary voltage of the single-phase transformer is 240 V and the secondary voltage is 250 V.…

Q: The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical…

A: Given data:Load - 1 :P1=950Wcosϕ1=0.5 Lagging Load-2:P2=1.14Wcosϕ2=1 Load-3:P3=760Wcosϕ3=0.5…

Q: If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary…

A: Wye connection: If we connect together the negative or positive terminal of the three-phase…

Q: I. Z The three-phase circuit shown in Figure 1 is composed of a balanced three-phase A-connected…

Q: How does a three-phase power system differ from a single-phase power system, and what are their…

A: Single-phase:- To complete the circuit, a single phase involves two wires: the conductor and the…

Q: A three-phase system has balanced conditions so that the per-phase circuit representation can be…

A: The three-phase system diagram is shown below, Here,The load voltage is,VL=4kVrmsThe load impedance…

Q: The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical…

A: Given data:Load -1 :P1=950Wcosϕ1=0.5 Load-2:P2=1.14Wcosϕ2=1 Load-3:P3=760Wcosϕ3=0.5 line voltage,…

Q: A generator is rated 100 MW. 13.8 kV and 90% power factor. The effective resistance is 1.5 times…

Q: Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results: 0.C.…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
Does an open connection permit balanced three-phase operation? - (a) Yes (b) No
Pls. write solution neatly
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
5.In three-phase transformers, the high voltage star connection is preferred. This is so because in this case A) The voltage on the star windings is lower than if they were in delta and this reduces manufacturing costs. B) The voltage on the star windings is higher than if they were in delta and this reduces manufacturing costs. C) The voltage on the star windings would be the line-to-line voltage of the system since it is a three-phase manufacturing transformer. D) THERE IS NO SOLUTION
SHOW COMPLETE SOLUTION A. What is the overall power factor of the two loads as seen by the source? Use two decimal places. B. Determine the magnitude of the current passing through Load 1. Use amperes and two decimal places. C. Is the overall power factor leading or lagging?
Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5 + j3 and 2 + j4.5 ohms are connected in parallel to a 7900-V source. Their secondaries are supplying a common load of 30 + j40 ohms. What is the magnitude of the voltage across the load in volts? (2 decimal places)
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
How does a three-phase power system differ from a single-phase power system, and what are their respective applications?
(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZRY = 50 +j50 Q , ZYB = 150 + j0 Q and ZBR= 50 – j50 N. (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.
1. For each of the three single-phase transformers below, the phase position of the primary voltage has been drawn on the phasor diagram to the right. On the same phasor diagram, draw and label the phase position of the secondary voltages VAC 1.a. 1.b. VBA VBA VcB 1.c. VCB