(read image please) 4. A cantilever beam supports a uniform load of intensity q = 80 lb/in that includes the weight of the beam. Thebeam is a steel W 10 X 12 wide-flange, for which I = 54 in. Determine the absolute maximum normal bendingstress in the beam.AL = 100 in.B10 in.IW 10 x 12

Answered: 4. A cantilever beam supports a uniform…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa. F 2.0 m E P = 30 kN 2.5 m D -3 m- -3 m-
A T-beam has the following properties: bf = 820 mm, bw = 250 mm, d = 470 mm, t = 100 mm. f’c = 20.7 MPa, fy = 414 MPa. Determine the required tension steel area when: a.MD = 175 kN-m, ML = 190 kN-m b.Find the maximum design moment so that its tension controlled. (USE c = 3d/8). Tension steel exactly experiences 0.005 strain. hello please answer that question,,thank you God bless
Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a base b= 140 mm and h= 240 mm PLACE THE ENTIRE PROCEDURE
3. The roof truss is subjected to the loadings shown. Determine the force in each member and indicate if the members are in tension or compression. Approximate each joint as a pin. 200 N 300 N 300 N 1.5 m D. B. 4 m 3 т G 3 m 3 m E 3 т Paist X Ute 150 N
The beams ABD and DE are joined by a hinge at D. Select the lightest allowable W-shape for beam DE if its working stress in bending is 120 MPa. Also calculate the actual maximum bending stress in beam.
The truss shown below supports a load located at J that is 221 kN. The horizontal and vertical members are each 1.387 meters in length. Determine the axial force (in kN) in member DG. Answer is -312.54. Show solution.
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm E 2а b а —
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1620 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 190 kip-ft, P = 26 kips, LAB = 3.6 ft, LBC = 5.4 ft. %3D %3D P V. MA C LAB LBC Answer: (a) VA = in. (b) VB = in.
125. A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E = 2x105 N/mm2. The elongation of %3D the bar will be 1 (b) 6n 1 mm (a) mm (c) -mm (d) -mm 2
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.75 m, b= 1m, d= 50mm, h= 10mm E D 2а b B b a
The strain in the x direction at point A on the A-36 structural-steel beam(in figure attacched) is measured and found to be εx = 260 x 10-6. Determine the applied load P. What is the shear strain γxy at point A? PICTURE ATTACHED.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1770 in.4]. For the loading shown, determine: (a) the bearn deflection at point.A. (b) the bearn deflection at point B. Assume MA = 250 kip-ft, P = 26 kips, LAB = 6.0 ft, Lec=9 ft. P MA В LAB LBC Answer: (a) VA = in. (b) VB = in,

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

4. A cantilever beam supports a uniform load of intensity q = 80 lb/in that includes the weight of the beam. The beam is a steel W 10 X 12 wide-flange, for which I = 54 in. Determine the absolute maximum normal bending stress in the beam. A L = 100 in. B 10 in. I W 10 x 12