Q54. A 1:10 scale model of a submarine movingfar below the surface of water is tested in awater tunnel. If the speed of the prototype is 8m/s, determine the corresponding velocity ofwater in the tunnel. Also determine the ratio1.121 x 10 m²/s, Ywater =1.00 × 10 m²/s,of the drag for the model and the prototype.= 1.00 x 10 m²/s,= 1000 kg/m.= 1.121 x 10-6 m²/s, yYsea waterwaterPsea water= 1027 Kg/m, Pwater%3D

Answered: Image /qna-images/answer/7724788a-ed40-4a1a-8d74-0f8b1e425a14.jpg

4. A 1:10 scale model of a submarine moving far below the surface of water is tested in a water tunnel. If the speed of the prototype is 8 m/s, determine the corresponding velocity or water in the tunnel. Also determine the raio of the drag for the model and the prototype. = 1.121 x 106 m²/s, Ywater = 1027 Kg/m, Pwa = 1.00 x 10 m²/s, = 1000 kg/m2. Ysea water %3D Psea water water

4. A 1:10 scale model of a submarine moving far below the surface of water is tested in a water tunnel. If the speed of the prototype is 8 m/s, determine the corresponding velocity or water in the tunnel. Also determine the raio of the drag for the model and the prototype. = 1.121 x 106 m²/s, Ywater = 1027 Kg/m, Pwa = 1.00 x 10 m²/s, = 1000 kg/m2. Ysea water %3D Psea water water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The diagram below shows a pumping system to pump water to an elevated tank. The next page shows the performance curve of a specific type of centrifugal pump. The loss factors at the inlet and outlet are 0.5 and 1.5 respectively while the loss factor associated with the bend is 1.5. The diameter of the pipe is 0.050 m while the total pipe length is 400 m. In order to simplify the calculation you can assume that the friction factor is f= 0.036. Determine the duty point of this pumping system and thus determine the flow rate of the pump for an impeller diameter of 140 mm? Also determine the shaft power of the pump and give an estimate of the pumps efficiency at the duty point. Given that the pump is located 1.80 m above the water surface (1), and the pipe length from inlet to pump is 6.0 m, determine the NPSHA at the pump and state whether cavitation is likely to occur. Sol: 3.6 m 40 H m 30- P 10 20- K₁ = 0.5 5- kW 2- 1- 13 4 2- NPSH K₁ = 1.5 170 160 150 140. 130_ (1) Q 10 Pump 20 54…
The 2-kg spool S fits loosely on the inclined rod for which the coefficient of static friction is μ = 0.29. (Figure 1) Figure 0.25 m s ▸ Part A If the spool is located 0.25 m from A, determine the maximum constant speed the spool can have so that it does not slip up the rod. Express your answer to three significant figures and include the appropriate units. Value Submit Provide Feedback 4 Request Answer Units ?
Help
A small boat weighing 40 LT has a submerged volume of 875 ft3 when traveling at 20knots in seawater. (ρ = 1.99 lb-s2/ft4 ; 1 LT = 2240 lb) a. Calculate the magnitude of the hydrostatic support being experienced by boat.b. What other type of support is the boat experiencing?c. Calculate the magnitude of this other type of support.d. What will happen to the submerged volume of the boat if it slows to 5 knots? Explain your answer.
A floating house will be projected as shown in the figure. The basement of the house will be in the form of an open concrete box. The height of the concrete box will be 0.60 m above the water surface. All other dimensions of the wooden house will be chosen by you. Other assumptions will be made by you if necessary. Compute the weight of concrete box, weight of house and the total weight of the system for 4 people living in the house. Wood 0.60m Concrete
1. Compute the R1 value in newton for the beam 2. Compute the R2 value in newton for the beam 3. Compute the midspan value of Ely for the beam in two decimal places and in terms of kN-m³
Please refer to the figure below. Determine the magnitude of the resultant couple at point D in Ib-ft. 20 1ы 200 kg 250 N 20 kN m 2 FT 200 kg