4 Why is reinforced concrete so popular in building construction projects? 5 Why are the steel rods placed below and as far away as possible from the neutral axis in a reinforced concrete beam? 6 The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section. 550 mm 75 000 200 400 mm

4 Why is reinforced concrete so popular in building construction projects? 5 Why are the steel rods placed below and as far away as possible from the neutral axis in a reinforced concrete beam? 6 The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section. 550 mm 75 000 200 400 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

! Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm 8 mm 8 mm Aluminum 24 mm -Steel Determine the maximum stress in steel when the bar is bent about a horizontal axis, with M= 56 N.m. The maximum stress in steel is - MPa.
What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681
1. Find the properties of equal-leg angle bar 150 x 50 x 6.0 in metric. 2. Find the full section properties of LC shapes steel bar 100 x 50 x 15 x 3.0 in metric. 3. A stress that lies between the proportional limit and the upper yield point of a steel. What is 5 and 5 Show the relationship uring a graph of mild structural stool
A 26-foot-long structural steel bar is being tensed along its centroidal axis. Point B is being tensed by 180 kips of force and point C is being tensed by 121 kips of force. The bar has a rectangular cross-section with a height of 3.6 inches and width of 2.8 inches. The steel is HSLC steel with a yield stress, oy = 50 ksi and modulus of elasticity, E = 30,000 ksi. Show all work and any assumptions clearly. Record your answers on the answer key. Complete the following: ): Calculate the axial stress in sections AB and BC of the beam. Does the calculated stress in either section exceed the yield stress of the steel? Calculate the deformation in sections AB and BC of the beam. What is the total axial deformation that the beam experiences? What is the final length of the beam? Calculate the factor of safety that this structural bar was designed for. w = 2.8 in. A B 180 k C 121 k Answer Key σ > Gy Yes or No * 18 ft 8 ft Axial Section Stress (ksi) AB BC Total Deformation, 8 (in) Final Length…
Please answer, Asap. Thank you.
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
The composite bar shown is fixed at the ends and is subjected to the axial load P shown. If the aluminum is stressed to 10 ksi, find the force P and the stress in the steel. 10in. 15in. Aluminum Steel A=1.5 in? E=10x10°psi A=2.0 in? 6 E=30x10°psi 6
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Steel Eg = 200 GPa Acp= 39 mm? Aluminum Соpper Eg = 70 GPa AAB= 58 mm? Ecu = 126 GPa ABc = 77 mm? 16 kN 8 kN 9 kN 7 kN 16 kN 8 kN – 450 mm- -300 mm- 400 mm-
A flat bar of aluminum alloy 25 mm wide and 5 mm thick is placed between two steel bars each 25 mm wide and 10 mm thick to form a composite bar 25 mm x 25 mm as shown. The three bars are fastened together at their ends when the temperature is 15℃. Find the stress in each of the materials when the temperature of the whole assembly is raised to 55 ℃.Steel: Es = 200 GPa; Coefficient of expansion = 1.2x10^-5/℃.Aluminum: Eal = 200/3 GPa; Coefficient of expansion = 2.3x10-5/℃.
The compound bar ABCD has a uniform cross-sectional area of 0.25 in.² When the axial force P is applied, the length of the bar is reduced by 0.018 in. Determine the magnitude of the force P. The moduli of elasticity are 29 x 10^6 psi for steel and 10 x 10^6 psi for aluminum. Please include the details. Thank you.