4) Which working medium gives precise control over motion(A) hydraulic,(B) pneumatic,(C) both of hydraulic or pneumatic5) In fluid power systems, form of energy is transformed from pressure to kineticenergy in the(A) Actuators,(C) power supply section,section.(B) power control section,(D) fluid filtering component(s)6) AND-logic valve passes input to output if(A) both of the input ports have no flow,(B) only port one of the input ports have flow(C) only port two of the input ports have flow,(Dj both of the input ports have flows

4. Ans: option B is correct. (Pneumatic) Precise control over motion is easy with pneumatic system.…

4) Which working medium gives precise control over motion (B) pneumatic, (C) both of hydraulic or E (A) hydraulic, 5) In fluid power systems, form of energy is transformed from pre energy in the (A) Actuators, (C) power supply section, 6) AND-logic valve passes input to output if (A) both of the input ports have no flow, (B) only port one of the input ports have flow (C) only port two of the input ports have flow, section. (B) power control section, (D) fluid filtering component(s,

4) Which working medium gives precise control over motion (B) pneumatic, (C) both of hydraulic or E (A) hydraulic, 5) In fluid power systems, form of energy is transformed from pre energy in the (A) Actuators, (C) power supply section, 6) AND-logic valve passes input to output if (A) both of the input ports have no flow, (B) only port one of the input ports have flow (C) only port two of the input ports have flow, section. (B) power control section, (D) fluid filtering component(s,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is importance of these components in IC engines 1. Inlet manifold 2. Connecting rod 3. Camshaft
Please answer all questions or leave for someone else to answer. A feedwater heater, operating in steady state, has 2 inlets and one outlet, at inlet 1 steam enters at a pressure of 5Mpa, a temperature of 275°C with a mass flow rate of 40kg/s. At input 2 it is liquid water at a pressure of 5Mpa at 40°C and through a surface of 25cm ^2, at output 3 there is a volumetric flow of 0.06m^3/sec. Determine: a) mass flow of input 2 and 3 b) speed at input 1 c) enthalpy at output 3 d) outlet temperature in 3 e) the quality value if any
As a future Mechanical Engineer, how will you express the connection between level, flow, temperature, and pressure control systems in any engineering field? Expand your answer
Thermodynamics -heat transfer. Show complete work
1- During a steam generator performance test, the following data were taken: Fuel data: Type=Coal Mass flow rate=2.5 kg/s High heat value=32.5 Mj/kg Steam data: Pressure=13 bar Dryness fraction=99.5% Mass flow rate=25 kg/s Feed water data: Saturated at 50 C° Calculate the steam generator efficiency.
In a perpetual motion machine, how much energy is waste energy?
| Part of a refrigeration system operates at steady state with Refrigerant 22 as shown in the figure below. There is no significant heat transfer to or from the heat exchanger, valve, and piping. Kinetic and potential energy effects are negligible. State 1 is a saturated liquid. What temperature is it, in °F? Describe the refrigerant at state 4 as one of the following: compressed liquid, saturated liquid, tyro-phase mixture, saturated vapor, or superheated vapor. Determine the required mass flow for the given operating conditions, in lb/min. Determine the rate of heat transfer between the evaporator and its surroundings, in b. Btu/min. Make sure to clearly state the direction of heat transfer. 1. T=10°F P= 15 Ibf in (AV), = 9.5 ft/min. Pi= 120 Ibf/in.? Heat exchanger Throttling valve Evaporator P 15 lbfin.2 X3 = 1.0 P2= 15 lbf/in.2
This device is responsible for passing outside air over the water to remove the heat from the system. a) capacitor b) evaporator c) cooling tower In this type of reciprocating compressors, the compressor shaft and the electric motor shaft are the same part. b) open c) semi-hermetic a) hermetic
The Electric hand dryer is an example of........ loop system
3. At a load of 43,000 KW in a steam turbine generating set, 3600 RPM, the following data appear in the log sheet. Steam flow -190 Metric Tons/hour Steam pressure - 8.93 MPaa Steam temperature - 535C Feed-water temperature - 230 C Fuel Flow: Bunker Oil -3.4 Metric Tons/hr HHV=10,000 Kcal/hr Local coal -18 Metric Tons/hr HHV = 5350 Kcal/hr Determine the overall boiler efficiency. h at 8.93 MPa and 535°C -3475.7 KJ/kg hf at 230°C-990.12 KJ/kg
9.) The flow work relation (Wflow) is the same whether the fluid is pushed into or out of the control volume. Select one: True False 3.) For single stream devices like nozzles, the velocity usually become larger at the exit compared to the inlet that it also increases the pressure of the fluid flow. Select one: True False
Providing the Design Parameters for Equipment and Components in a Refrigeration and Cryogenic Plant for Liquid Oxygen Production, nitrogen is the refrigerant used, includes all the details each, includes sources link: Compressors: Flow rate = power consumption= discharge pressure= suction pressure = type of refrigerant = refrigerant mass flow rate = materials of construction = operating temperature range = Heat exchangers: Heat transfer coefficient, heat duty, temperature difference, pressure drop, type of fluid, fluid flow rate, materials of construction, and operating temperature range. Expansion valves: Type of valve, orifice size, refrigerant flow rate, materials of construction, and operating temperature range. Storage tanks: Capacity, insulation thickness, pressure rating, type of material, materials of construction, and operating temperature range. Pumps: Flow rate, head, power consumption, type of fluid, materials of construction, and operating temperature range.