4-The number of fill and half-address required to add 16-bit number is: * 8 half-adders, 8 full-adders O 4 half-adders, 12 full-adders O 1 half-adder, 15 full-adders O 16 half-adders, 0 full-adders 1- In a BCD-to-seven-segment converter, why must a code converter be utilized? * O to convert the 4-bit BCD into gray code to convert the 4-bit BCD into 7-bit code O to convert the 4-bit BCD into 10-bit code O No conversion is necessary.

4-The number of fill and half-address required to add 16-bit number is: * 8 half-adders, 8 full-adders O 4 half-adders, 12 full-adders O 1 half-adder, 15 full-adders O 16 half-adders, 0 full-adders 1- In a BCD-to-seven-segment converter, why must a code converter be utilized? * O to convert the 4-bit BCD into gray code to convert the 4-bit BCD into 7-bit code O to convert the 4-bit BCD into 10-bit code O No conversion is necessary.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

tal Laser Based Interferometers are used to measure air velocity and pressure. O a. False O b. True The ratio of output to input of a system is known as Transfer function. Select one: O True O False Select the simple system from the following. O a. Lamp with on/off switch O b. Air conditioner O. Closed loop room heating system O d. Speed control of Motor
Sl X g whall plel , joogle. louTube com/forms/d/e/1FAIpQ B2 P Laall Sl x + LScol9SMu); SATKIKTISHRMyHU oy 9-DXKy7QNjICApZy il yls] formResponse this is an electronic Circuit called ~----—_.__._»
Use the block diagram reduction please
Draw the block diagram and explain the basic components of Numeric relay
choose the right answer only plz
Write about this Just one page
858445655 O Blackboard Remaining Time: 59 minutes, 28 seconds. * Question Completion Status: 90 10 110 120 130 14D 150 160 440 450 46D 470 480 49D 500 10 70 18 19 201 40 50 36 370 38 3940 410 42 43D 20 QUESTION 35 What is indicator number 1 called. 6 1 Heading indicator Airspeed indicator O Altimeter indicator QUESTION 36 Attitude indicator is also known as: O Virtual horizon O Visual Horizon O Artificial Horizon Th Click Save and Submit to save and submit. Click Save All Answers to save all answers. MacBook Air
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
please answer in hand written i dont understand where i can put the exponent..
b) What is the difference between systematic and random errors; then list the reasons for equipment errors.
Answer the questions below. (Insert the numerical value only, do not use ,+, *, or) The Relative error for your answer should be less than 0.01, which means if the answer was 50, then the error should not exceed 50°0.01= +0.5! if the answer was 230, then the error should not exceed 230°0.01= ±2.3! if the answer was 2.31467 10^-3, then you should enter this value: 0.00231467, not this 0.0023 !!! Given the system shown, if L=0.275H and C=0.4F, then the value of R that yield 15% overshoot is (the output is the current through the inductor): ohm io(t) i(t) ↑ R . the value of the natural frequency is: rad/sec The value of the damping ratio is:
Do the following binary subtraction: 100001101.11011- 010010110.01110 (Note : The problem should be solved in separate paper with steps and scanned copy should be submitted along with other answers The final answer must be entered in the boxes below. Enter only one bit in a box and fill the unused boxes if any, with zeros) Answer - Integer part = Answer - Fractional part=