4 kN/m 3 kN Arti 6 kNm 3 m 3 m 2 m -

Q: From the given beam shown, and at the given point C, determine the following: a. the internal normal…

A: Consider the section ACB,

Q: Determine the reaction at pins at A, B and C and fixed support at D. Answer in component form. Take…

A:

Q: Draw the shear and moment diagram for the beam shown below by choosing the reaction at the interior…

A:

Q: A positive moment diagram of the real beam when loaded to a corresponding conjugate beam is directed…

A: The given statement is true.

Q: 6 m 360 kN/m - Im 100kN Im 60 kN/m I ㅏ 4 m

A:

Q: 60 lb 3 ft -4 ft-

A:

Q: |8.00 kips Sketch a Free Body Diagram of a BY section of the truss that facilitates determination of…

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer  Let us first draw the ILD for member DI. Pass a section through member DI as shown below…

Q: Determine the reactions at the supports and draw the shear and moment diagrams for members BC and CD…

A:

Q: A B D E 2.0000 2.0000 2.0000 2.0000

A: When any unit load is passing through the beam, then the reactions or shear forces are presented as…

Q: 5. Determine the force and moment reactions at A for the beam which is subjected to the load…

A: A propped cantilever beam with an overhang portion is given.To this beam, the beam is loaded…

Q: A beam is part of the framing system for the floor of an office building. The floor is subjected to…

A: Service dead load moment= 65 ft-kipsService live load moment= 63 ft-kips

Q: draw the shear and moment diagram, step by step pls

A:

Q: Assume that the loads are being transmitted to the bottom of the truss in the diagram below. For…

A: Answer  (a) Influence line diagram for member DI Consider a section passing through member DI as…

Q: 3. Determine the resultant of the force system in the figure. 450N 850 N 48° 350 N 55 500N

A:

Q: Ex3:A reinforced rectangular section has width (300mm) and effective depth (500mm) and f'.= 30Mpa ,…

A: Given data:

Q: Compute the support reactions of the given beam below. Also, determine the maximum value of the…

A:

Q: THIS IS FOR EXTRA CREDIT. Determine (a) the equations of the shear and bending- moment curves for…

A:

Q: Using the force method of analysis, determine the reactions at the supports then draw the shear and…

A:

Q: You didn't solve the problem correctly could you resolve it and please clarify your steps the…

A:

Q: 1. The frame shown is supported by pins at points A and B. A 360 N force is applied on the rope that…

A: Consider the support reaction ∑Fx=0⇒HA+HB=0∑Fy=0⇒VA+VB=360∑MA=0⇒-HB×1.8-360×2.6HB=-520 N, HA=520…

Q: Determine the reactions at the supports, then draw the shear and momont diagrams. Use the slope…

A: Given beam: To determine: Shear Force and Bending Moment Diagrams All supports are fixed

Q: B 3 m 1.5 m A. Draw the shear force and the bending moment diagrams, V and M for the simply…

A:

Q: Determine the moments at all supports. Use MOMENT DISTRIBUTION METHOD

A: To determine the moments at all supports Using MOMENT DISTRIBUTION METHOD.

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: B

A:

Q: F. Draw the shear force and bending moment

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: Determine the internal normal force at point C of the beam. Give your answer in N and to 3…

A: Given:Required:Internal normal force at C

Q: A statically indeterminate beam, in which the horizontal forces at the left and right ends (points A…

A:

Q: In the given system, a- Find the support reactions and the joint forces. B- Draw the inner force…

A:

Q: The simple beam AB shown in the figure is subjected to a concentrated load P and a clockwise couple…

A: A simply supported beam is given as shown in the figure above and it has been asked in the question…

Q: Find the stresses in the wires P1, P2, P3 shown if their diameters are 100mm  each and P3=20kN and…

A: Given data: R=40 Kn P3=20 Kn   It is asked to calculate forces P1 and P2

Q: 1.) For the beam shown, determine the reactions at supports A, B, and C. then draw the SHEAR and…

A: Force method: Three moment method (Clapeyron's theorem) is used for analysis of above beam.

Q: A beam is subjected to the loading condition shown below. Draw the influence lines for: a) the…

A:

Q: For the beam and loading shown, (a) draw the shear and bending- moment diagrams, (b) determine the…

A: Given that....

Q: Q4 Draw the influence lines for (a) the vertical reaction at B, (b) the shear just to the right of…

A:

Q: The free-body diagram of roller C is shown with the truss members assumed to be in tension. AC BC…

A:

Q: Draw the shear and moment diagram, determine the maximum value.

A: ∑MB=0-P×L2 + 2P×L2 - RD×L + P×L+L2=0RD=2P∑V=0RB+RD=P+2P+PRB+2P=P+2P+PRB=2PShear force at E=PShear…

Q: 9. Using the Method of Sections, determine the force in member BC, to the nearest 1 Ibs. (Hint: Find…

A: