the beam is subjected to a load F=400N and is supported by the rope and the smooth surfaces at A and B.a. Draw the free body diagram of the beamb. what are the magnitudes of the reactions at A nand B? 1. The beam is subjected to a load F = 400 Nand is supported by the rope and thesmooth surfaces at A and B.a. Draw the free-body diagram of thebeam.45°30b. What are the magnitudes of thereactions at A and B?1.2 m-1.5 m–B

Answered: Image /qna-images/answer/4891adc2-17b6-459d-a31a-35f62a87def2.jpg

the beam is subjected to a load F=400N and is supported by the rope and the smooth surfaces at A and B. a. Draw the free body diagram of the beam b. what are the magnitudes of the reactions at A nand B?

the beam is subjected to a load F=400N and is supported by the rope and the smooth surfaces at A and B. a. Draw the free body diagram of the beam b. what are the magnitudes of the reactions at A nand B?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the degree of determinacy of the structure shown below. Put "-1" if unstable, "0" if determinate and the degree of indeterminacy if indeterminate. NEA
don't answer the X figure, just answer the d and e
1. 1 For the beam shown below, (a) Draw the V-Diagram (b) Draw the M-Diagram (c) Find the largest value of o, and give the (x,y,z) coordinates of its location. (d) Find the largest value of 7y and give the (x,y,z) coordinates of its location. List of beam properties List of displacements List of forces of single-point constraints (these are the reactions at the supports) List of forces in beam elements List of stresses in beam elements S = 0.05" Si = 0.04" 30" Cross section Aluminum 50.000 in.lb E- l0xIo psi V=0. 3 60"
A structure is externally stable if: A. Reactions are concurrent B. Members experience rigid body movement C. Both A and B D. Neither A nor B
3 ft 100 lb 3 ft- 200 lb-ft 2 ft 000 Az □ Ay DO 000 NA along the rod MA B₂ By Fa perpendicular to the rod No perpendicular to the surface at B MB L. Identify the support reactions on the smooth uniform bar shown in (Figure 2). Check all the possible support reactions on the beam, even if some of them are equal to zero due to the loading given. Make sure the reactions in the set you choose do not depend on each other.
STFIFFNESS METHOD Example: Use the stiffness method to determine the reactions then draw the BMD for the shown beam.
A compound beam as shown with a pin at A, a hinge at C, and rollers at B and D,1) Draw all F.B.D.s for your calculation;2) Determine the reactions at A, B and D when the beam is in equlibrium [Hint: 1) ABC part is the independent part and CD is the dependent part of the compound beam. The analysis always starts from the dependent part, then the independent part. 2) Draw the FBD of CD part first.]
1. Given: A structure shown below Find: (1) Determine the magnitudes and locations of the two distributed loadings. In other words, determine the magnitude and location of the loading between A and C, and those of the loading between D and B. (2) For the member DEB, (a) take the moment at B and find the reaction at E and (b) then find By by either Fy= 0, or EMp = 0. (Recall that support conditions at B and E are rollers, so there are no reactions in x-direction.) (3) For the whole structure, 3 unknown forces and moment at A (Ax, Ay and Ma) are the only unknowns. Determine those 3 unknowns at A. 900 N/m 900 N/m B A C D 2E - 3 m 3 m - 4 m - 3 m3 m-
80 mm, A E -170 mm B D C 125 mm 75 mm Problem 06.085.a - Frame with 2-force member Determine the components of the reactions at A and E if a 930-N force directed vertically downward is applied at B. The components of the reaction at A are: Ax = lb- Ay = lb t The components of the reaction at E are: E₁= lb→
Zero-Force Members are structural members that support No loading but aid in the stability of the truss. Tips on getting the zero-force members: 1. there is no external load or reaction at that joint 2. Insufficient structural members to satisfy or "balance" the system: Summation of forces along the horizontal and vertical 3. two of the members are collinear As shown in the figure, structural members of zero-force members can be noticed through observation. Load P Н. F A C D E At a glance, it can be inferred that the member FG and FE are zero force members, because: First, there is no external load applied on the joint
The central rod CD of the set below is heated from T1 = 30ºC to T2 = 180ºC by an electrical resistance. At the lowest temperature, the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel and each have a cross-sectional area of 125 mm2. CD is made of aluminum and has a cross-sectional area of 375 mm2. Use EFe = 200 GPA, EAl = 70 GPA, αFe = 12 x 10-6 /°C, and αAl = 24 x 10-6 /°C. answer: 5.4 kN
Compute for the Shear and Moment Equation each segment. Compute the Reactions and Draw the detailed Shear and Moment Diagram indicating values.