Segments AB and BC of the assembly are made from 6061-T6 aluminum and A992 steel, respectively. The assembly is fixed at A and C. The couple forcesP= 3.5kip are applied to the lever arm. The shear modulus of elasticity 6061-T6 aluminum alloy is3.7 ? 103 ksi, and for %3D A992 steel is 11 ? 103 ksi. Determine the maximum shear stress developed in segment AB. Determine the maximum shear stress developed in segment BC

Segments AB and BC of the assembly are made from 6061-T6 aluminum and A992 steel, respectively. The assembly is fixed at A and C. The couple forcesP= 3.5kip are applied to the lever arm. The shear modulus of elasticity 6061-T6 aluminum alloy is3.7 ? 103 ksi, and for %3D A992 steel is 11 ? 103 ksi. Determine the maximum shear stress developed in segment AB. Determine the maximum shear stress developed in segment BC

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
A stress developed if the applied force is parallel to the resisting area refers to: O tangential O bearing O normal. O simple
Question 4a pls
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d, = 1.5 in.; both have length L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are bj = 80 mm, d1 = dz 240 mm, b2 = 10 mm, d2 = The di- di %3D %3D 120 mm, and a = 60 mm. Deter- (2) (2) (1) mine the maximum bending stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment M = +6,000 N m is applied about the z axis. Assume that E = 12.5 GPa and E2 = 70 GPa. FIGURE 3 %3D