4 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 24 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. B C Te 30mm 0.6m 0.8m 04m Te= 5 KN-m Te= 7KN-m

4 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 24 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. B C Te 30mm 0.6m 0.8m 04m Te= 5 KN-m Te= 7KN-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid shaft is fixed to the support at Cand subjected to the torsional loadings TA = 12 kN.m and TB = 3 kN.m in the directions shown by the figure. What is the angle of twist of end A with respect to end C? Take d = 120 mm, LAB = 263 mm, L BC = 184 mm and G = 75 GPa. %3D Tg LBc TA LAB
A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques as shown in the figure. Using the principle of superposition, determine the maximum permissible value of T subject to the following conditions: T ≤ 83 MPa, Tal ≤ 55 Mpa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 Gpa and for aluminum, G = 28 Gpa. C Steel 50 mm 900 mm Aluminum 40 mm Ø 600 mm
T.L Tr4 %3D J = " (r* – rf) (Tubular shaft) Tr (Solid shaft) G.J 3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to 50 diameter steel segment. The ends of the shaft are attached to rigid supports (fixed supports). Calculate the absolute maximum shear stress developed in each segment when the torque T= 5.1 kN-m is applied (a = 2 m and b = 1.5 m). Use G = 35 GPa for bronze, and G = 75 GPa for steel. (21 pts) 75 mm 50 mm Bronze Steel
The circular cross-section, L=0.5m long console BC shaft in the figure is forced to twist with P1=2 kN, P2=8 kN due to the forces on the belts connected to the pulley C. The radius of the pulley is R=0.4m and its weight is W=3 kN. Calculate shaft diameter D based on the assumption of maximum shear stress (TRESCA). Yield strength of the shaft = 240MPa and safety factor is S=2 1 kasnak D 2R P2 |B kayış y
A rope pulley is supported by two deep groove ball bearings as shown in the figure. A force of FR = 7 kN acts on the pulley in the radial direction. If Fa = 0.5kN, axial force acts. The rolling diameter of the pulley is d = 300 mm and the rope speed is v = 4 m / s. The nominal life of the bearings is required as Lh = 27000 h. Since the diameter of the shaft where the bearing is bearing is 45 mm, choose the appropriate bearing. V = N.D.n
In the figure, there is a steel shaft where moment is applied from the C point. The modulus of elasticity of this shaft is 210 GPa and its shear modulus is 80 GPa. The material of the shaft is Ç1010 and the yield stress is 240 MPa.Find the shaft diameters Dab, Dbc, Dcd, Dde and the torsion angle between A and E according to the Vonmises hypothesis by taking the safety coefficient as 2
A shaft ABCD is supported by a clamp at point A and is subjected to point torques at B, C and D, as shown in the figure. The shaft has variable cross-section and is solid in segments AB and CD and hollow in segment BC. The lengths and diameters of each segment are shown in the figure. Assume that the deformation is linear elastic and take the shear modulus of elasticity G = 12.1 × 10° psi. a) Using method of sections, plot the torsion moment diagram. b) Find the angle of twist for the free end (point D) with respect to the fixed support at A, QAD and the angle of twist for point C with respect to the fixed support at A, QCA. Find both angles in degrees. d₁ = 4 in d20 3.5 in, d2=2.5 in d3 = 3.0 in 25 kip-in 20 kip-in 10 kip-in A 20 in B с D ++ 25 in 30 in
H K T A solid shaft is subjected to forces and a torque as shown in figure. The diameter of the shaft is 35 mm, T=75 N.m., V=3 kN, P=4,7 kN and L=117 mm. Determine the shear stress (T) at point H (MPa). Note: If the stress has negative direction, use sign. Yanıt:
A turning force of 4 kN parallel to the "y" axis will be applied at the C point of the arm connected to the steel shaft AB in the figure. Accordingly, find the safe diameter value of the AB shaft using TRESCA and VON-MISES criteria.
Mechanics of Deformable Bodies
P-2 kN d- 60 mm Q= IkN 600 mm 1m Calculate the safe shear stress value of the shaft, given that the smallest allowable diameter d of the shaft subjected to forces P and Q is given as 60 mm in the figure?
A torque of Tx=200Nm and a torque of Mz=260Nm are applied to the stepped shaft in the figure. Calculate the maximum stresses that will occur in the bar section, taking into account the stress concentration.