324. A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in Fig. P-324. For steel, G 83 GN/m2; for aluminum, G = 28 GN/m²; and for bronze, G.= 35 GN/m2. Determine the maximum shearing stress developed in each Ans. TB %3D %3D segment. 472 N m; TAl 9.3 MN/m2 %3D Tc 300 N m Tp 700 N m %3D TA Steel Aluminum D Bronze 25 mm dia. 25 mm dia. 50 mm dia. 2 m 1.5 m 1 m·

324. A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in Fig. P-324. For steel, G 83 GN/m2; for aluminum, G = 28 GN/m²; and for bronze, G.= 35 GN/m2. Determine the maximum shearing stress developed in each Ans. TB %3D %3D segment. 472 N m; TAl 9.3 MN/m2 %3D Tc 300 N m Tp 700 N m %3D TA Steel Aluminum D Bronze 25 mm dia. 25 mm dia. 50 mm dia. 2 m 1.5 m 1 m·

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide clear/complete solution and diagram for this problem. A 10 m length shaft is used to transmit 50 kw power at 450 rpm. If the shaft stress is limited to 40 Mpa, find the angular deflection of the steel shaft. A. 4.23o B. 8.340 C. 7.23o D. 11.27o
1. A solid cylindrical rod is made of brass (G = 39 GPa); the rod has a diameter of 42 mm and is 750 mm long. The maximum allowable shear stress is 55 MPa and the twist cannot exceed 4° degrees. Determine the maximum allowable torque that can be applied. (Hint: check both conditions.) Ans. T= 800 Nm
i need the answer quickly
Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
A steel shaft (G = 80 GPa) with an external drive of 30mm must transmit a torque of 2700 N-m. The allowable shear stress in torsion is 120 MPa and the allowable rotation for the member is 0.1 rad / m. Design to the nearest millimeter the internal radius required for the steel drive
A steel shaft with a diameter 45 mm and length 1.30 m transmits 55.50 kW from an electric motor to a compressor. The allowable shear stress is 51.75 MPa and the allowable angle of twist is 2.1 degrees. G=83x10^3 psi Determine the polar moment of inertia (in mm^4) of the steel shaft. Determine the required torque (in N-m) as limited by stress. Determine the required torque (in N-m) as limited by the angle of twist.
A shaft fixed to a wall at B is made of an outer steel tube of 1" outer radius (G = 11,400 ksi) bonded to an inner solid brass core (G = 5200 ksi) of 0.5" radius. For the torque applied at A determine the maximum shear stress in each material and the rotation of A. Note: Each material carries part of the total applied torque. Treat end A %3D as a joint. Ans: 1977 psi steel, 451 psi brass 4 ft 0.5 in. 1 in. T= 250 lb-ft (a) all cunnorted at A and B. For
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
only Handwritten answer needed please. not typed
-10 108 (mm) Figure 5.41 5.21 Determine the St Venant torsion constant for the thin tapered section in Fig. 5.41. Hence derive an expression for the shear stress acting along the longer edges in terms of the torque T when the thickness 10 st s 1. If T = 15 Nm estimate the position and magnitude of the maximum shear stress from a consideration of contours of constant shear stress
Q5.A stepped shaft has the appearance shown in figure below. The region AB is aluminum, having G = 28GPA and the region BC is steel having G = 84GPA. The aluminum portion is of solid circular cross section 45mm in diameter and steel region is circular with 60mm outside diameter and 30mm Inside diameter. Determine the maximum shearing stress in each material where a torsional load of 4000N.m is applied. Ends A and C are rigidly clamped. 45 mm B TR 60 mm 30 mm (10 marks) 4000 N - m 2 m 12m 2m 1.2 m-
A hellcal spring Ils made by wrapplng steel wire 20 mm diameter around a forming cyllnder 160 mm in diameter. Calculate the elongatilon of the spring wlthout exceeding a shearing stress of 150 MPa If It ls composed of 20 turns. Let G=80,000 MPa. (Ans. 127.4 mm)