ExampleA hollow alu ninum tube of rectangular cross section is subjectedtorque of 56.5 KN.m along it's longitudinal axis.videDetermine the shearing stresses and the angle of twist. AssumeG= 28 GPL.t₁ =0.012با ما0.5t₂ =0,006A20,0060.25

We know that a hollow aluminum tube with a rectangular cross section is subjected to a torque of…

Example A hollow alu ninum tube of rectangular cross section is subjected mate / torque of 56.5 KN.m along it's longitudinal axis. Determine the shearing stresses and the angle of twist. Assume G= 28 GP. t₁ =0.012 0.5 t₂ =0,006 A 0,006 t₂ = 0,01 0.25

Example A hollow alu ninum tube of rectangular cross section is subjected mate / torque of 56.5 KN.m along it's longitudinal axis. Determine the shearing stresses and the angle of twist. Assume G= 28 GP. t₁ =0.012 0.5 t₂ =0,006 A 0,006 t₂ = 0,01 0.25

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hollow aluminum tube used is a roof structure has an outside diameter d2=70mm and inside diameter d1= 50mm. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.) If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist in degrees when the max shear stress is 50MPa? b.) What diameter 'd' is required for a solid shaft to resist the same torque with the same maximum stress?
In an experimental determination of principal stresses a cantilever of hollow circular cross section is subjected to a varying bending moment and torque; the internal and external diameters of the cantilever are 40 and 50 mm, respectively. For a given loading condition the bending moment and torque at a particular section of the cantilever are 100 and 50 Nm, respectively. Calculate the maximum and minimum principal stresses ata point on the outer surface of the cantilever at this section where the direct stress produced by the bending moment is tensile. Determine also the maximum shear stress at the point and the inclination of the principal stresses to the axis of the cantilever. The experimental values of principal stress are estimated from readings obtained from a 45° strain gauge rosette aligned so that one of its three arms is parallel to and another perpendicular to the axis of the cantilever. For the loading condition of zero torque and varying bending moment, comment on the…
Part A The solid shaft cross-sections shown are subjected to the externally applied torques shown. Compare the corresponding shear stresses developed in each shaft at point P. P P 2 T Rank the solid shafts from the largest shear stress at P to the smallest shear stress at P. (For example, 4> 3 = 1 > 2). 0.5 T
A hollow steel tube used in a roof structure has an outer diameter, di = 104 mm and inner diameter, d2 = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MРа.
b a A steel shaft of solid elliptical cross section has a semi-major axis of length, a, and a semi-minor axis of length, b, as shown in the accompanying figure. Given that a = 25 mm and b = 13 mm in this case, and given that the yield stress of the steel is 300 MPa, calculate the shear stress at point P in the accompanying figure when a torque of 550 Nm is applied to the shaft. Enter your answer in units of MPa to 2 decimal places.
-10 108 (mm) Figure 5.41 5.21 Determine the St Venant torsion constant for the thin tapered section in Fig. 5.41. Hence derive an expression for the shear stress acting along the longer edges in terms of the torque T when the thickness 10 st s 1. If T = 15 Nm estimate the position and magnitude of the maximum shear stress from a consideration of contours of constant shear stress
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 e Textbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
A hellcal spring Ils made by wrapplng steel wire 20 mm diameter around a forming cyllnder 160 mm in diameter. Calculate the elongatilon of the spring wlthout exceeding a shearing stress of 150 MPa If It ls composed of 20 turns. Let G=80,000 MPa. (Ans. 127.4 mm)
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.