30 30 15 15 Slab Slab Slab Slab -One-way slab spans between the beams #3 stirrup. 32" iiGirder ii %3D Girders span the shorter direction iBeam 3- #9 Beams span the longer direction Column 3- #9 - - 15"

Q: An interior column is to be designed as a part of an unbraced frame system, located at the ground…

A: Le = kL = 1*3 = 3m = 3000 mmPu = 1.2*300 + 1.6*350 = 920 KNFor A36fy = 250N/mm2

Q: a. calculate the forces on the rod by using analysis(calculation) method

A: Note - We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: 6m 60cm Water e timber 6m long with a cross section of 30cm x 30cm and a specific gravity of 0.72.…

A:

Q: In the truss shown below, find Load in member CD? Also find if it is in tension or compression? 4m]…

A:

Q: PLEASE SHOW WORK NEATLY. I NEED THIS TO STUDY. THANK YOU.  SUBJECT IS "STEEL"

A: Step 1:Step 2:Step 3:Step 4:

Q: The Built Up Beam shown is made by connecting two channel shapes and two plates, using 0.75"…

A: Draw the schematic diagram for the beam as follows:

Q: 1.) Draw the Free-Body Diagram for each mechanism shown. Provide a direction a a name for each…

A: To draw FBD

Q: 2/58 The cantilevered W530 x 150 beam shown is subjec- ted to an 8-kN force F applied by means of a…

A: Given a cantilever beam W530×150 subject to a force of 8 kN. It is asked to determine the equivalent…

Q: Instruction : Draw a matrix / table to show comparison of the following methods of analyzing…

A: Double integration method ∑MRb =0   4 Rc +30×1×12=30×4×42  4Rc =240-15    Rc =2254=56.25 KN…

Q: Design Column B2 shown on the floor plan, as a square tied reinforced concrete column. The column is…

A:

Q: Compute vmax and mmax for beam 1 and girder 1 in the roof framing plan  total load = 87psf B1 = W16…

A: Step 1:Step 2:Step 3:

Q: Problem 1a. Determine whether each of the beams and frames below are internally determinate,…

A: No. of reaction = (3 for fixed 2 for hinge 1 for roller)  a.)No. of Reaction = 4 (2+1+1) (2 for…

Q: 17. Determine the net width for a 10×1/2 in. plate with 3/4 in. bolts placed in three lines as shown…

A:

Q: use autocad Draw the structural details of the following sections (an elevation view and a side…

A:

Q: 3. Two 10”-15.3 lb channels are welded together as shown in the figure. Find the moment of area of…

A:

Q: The floor system used in a school classroom consists of a 4 in. Reinforced stone concrete slab.…

A:

Q: -3 ft- 100 16 -3 - B 200 ft 2 ft

A: Reference : Structural Analysis, Beam analysis Given data : A beam with load acting on beam 3ft from…

Q: use autocad -  Draw the structural details of the following sections (an elevation view and a side…

A: To draw the structural details of a steel connection in AutoCAD, you'll need to include both…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.