3.The shaft is made of A992 steel with the allowable shear stress of Tallow = 75 MPa. If gear B supplies 15 KW of power, while gears A, C and D withdraw 6 KW, 5KW and 4 KW, respectively, determine the required minimum diameter d of the shaft to the nearest millimeter.Also, find the corresponding angle of twist of gear A relative to gear D. The shaft is rotating at 600 rpm.

3.The shaft is made of A992 steel with the allowable shear stress of Tallow = 75 MPa. If gear B supplies 15 KW of power, while gears A, C and D withdraw 6 KW, 5KW and 4 KW, respectively, determine the required minimum diameter d of the shaft to the nearest millimeter.Also, find the corresponding angle of twist of gear A relative to gear D. The shaft is rotating at 600 rpm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 20 of 20 < A Water Balloon Battle. You are launching water balloons at a rival team using a large slingshot. The other team is set up on the opposite side of a flat-topped building that is 30.0 ft tall and 50.0 ft wide. Your reconnaissance team has reported that the opposition is set up 10.0 m from the wall of the building. Your balloon launcher is calibrated for launch speeds that can reach as high as 100 mph at angles between 0 and 85.0° from the horizontal. Since a direct shot is not possible (the opposing team is on the opposite side of the building), you plan to splash the other team by making a balloon explode on the ground near them. If your launcher is located 55.0 m from the building (opposite side as the opposing team), what should your launch velocity be ((a) magnitude and (b) direction) to land a balloon 5.0 meters beyond the opposing team with maximum impact (i.e. maximum vertical speed)? (a) Number i (b) Number i Units Units UNITS CHOICES: no units, degrees, s,…
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
Topics: Statics of Rigid Bodies, Equilibrium of Rigid Bodies, Equilibrium in Two Dimensions, etc. I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” Thank you for your help. PS: If you have answered this already, don’t answer it again; give chance to other experts to answer it. I want to verify if all of you will arrive in the same final answer; thats why I ask it multiple times.
Learning Goal: A centroid is an object's geometric center. For an object of uniform composition, its centroid is also its center of mass. Often the centroid of a complex composite body is found by, first, cutting the body into regular shaped segments, and then by calculating the weighted average of the segments' centroids.An object is made from a uniform piece of sheet metal. The object has dimensions of a = 1.45 ft, where a is the diameter of the semi-circle, b = 3.24 ft, and c = 2.10 ft. A hole with diameter d = 0.500 ft is centered at (1.13, 0.725). Figure X 1 of 2 Part A Find the area of the body. (Figure 1) Express your answer numerically in feet squared to three significant figures. ► View Available Hint(s) VE ΑΣΦ41 | vec A = 1.52 Submit * Incorrect; Try Again; 5 attempts remaining Part B I= Find I, the x-coordinate of the body's centroid. (Figure 1) Express your answer numerically in feet to three significant figures. ► View Available Hint(s) Submit Previous Answers Part C y =…
Note:- Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. Answer completely. You will get up vote for sure.
PROBLEM 1 For the engineering activity, current practical capacity is defined by the following requirements: 6,000 engineering hours for each product group that has been on the market or in development for 5 years or less, and 2,400 hours per product group of more than 5 years. Four product groups have less than 5 years' experience, and 10 product groups have more. There are 24 engineers, each paid a salary of P60,000. Each engineer can provide 2,000 hours of service per year. The actual engineering usage was 46,000 hours. The standard is 58% of current practical activity capacity. Case 1: Calculate the (1) activity volume and (2) unused capacity variances for the engineering activity Case 2: Suppose the operational managers have selected some improvement measures that promise to reduce non-value-added activity usage by 40% in the following year. Using the targeted reduction, establish kaizen standards for engineering, expressed both in physical and financial measures
WILL SURELY GIVE AN UPVOTE IF ANSWEREDSUBJECT: THERMODYNAMICSINSTRUCTION: FOLLOW THE SET OF INSTRUCTIONS THAT IS LISTED IN THE IMAGE. Will Not Violate The Academic Integrity/Honor Code Violation.
solve questions (7, 8 and 9)
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Help!!! Please answer part b correctly like part A. Please!!!!
Detail solution required with explaination