3.44 An aluminum tube with the hexagonal cross section shown is 2.5 ft long and has a constant wall thickness of 0.080 in. Find (a) the largest torque that the tube can carry if the shear stress is limited to 7200 psi; and (b) the angle of twist caused by this torque. Use G = 4 x 10 psi for aluminum. -15 in - 0.075 in FIG. P3.44

3.44 An aluminum tube with the hexagonal cross section shown is 2.5 ft long and has a constant wall thickness of 0.080 in. Find (a) the largest torque that the tube can carry if the shear stress is limited to 7200 psi; and (b) the angle of twist caused by this torque. Use G = 4 x 10 psi for aluminum. -15 in - 0.075 in FIG. P3.44

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Equal torques T = 5 kip · ft are applied to the two steel bars with the cross sections shown. (Note that the cross-sectional areas of the bars are equal.) The length of each bar is 8 ft. Calculate the maximum shear stress and angle of twist for each bar. Use G= 12 × 10° psi for steel. 5 in. 10 in. 2 in. 1.0 in. (a) (b) FIG. P3.52
The shaft in Fig. (a) consists of a 3-in. -diameter aluminum segment that is rigidly joined to a 2-in. -diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the maximum shear stress developed in each segment when the torque T = 10 kip in. is applied. Use G = 4×106 psi for aluminum and G = 12×106 psifor steel
A 3-m aluminum tube with the cross section shown carries a 200 N-m torque. Determine the following: a) the Maximum Shear Stress in the tube b) The relative angle of rotation of the ends of the tube. (For aluminum, use G = 28GPA) 100 mm 50 mm 2.4 mm 1.2 mm
Show the complete process and free body diagram to get the answer below.
A solid circular shaft of a diameter 100 mm is subjected to an axial stress of 50 MPa. It is further subjected to a torque of 10 kN-m. What is the maximum principal stress experienced on the shaft?
B4 The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 Nm and an axial tensile force of 2 kN. Find: 500 Nm 500 Nm A 2kN 2kN (a) the tensile stress in the concrete;
b a A steel shaft of solid elliptical cross section has a semi-major axis of length, a, and a semi-minor axis of length, b, as shown in the accompanying figure. Given that a = 25 mm and b = 13 mm in this case, and given that the yield stress of the steel is 300 MPa, calculate the shear stress at point P in the accompanying figure when a torque of 550 Nm is applied to the shaft. Enter your answer in units of MPa to 2 decimal places.
A 3-m long thin-walled tube has an equilateral triangular cross-section with a constant thickness of 10 mm. If each side of the triangle is 200 mm measured at the median line and the applied torque is 40 kN-m, what is the angle of twist in degrees? (Use G=70 GPa) (Round your answer to 3 decimal places)
Could you please solve A, B and C
Answer by step of mechanical deformable bodies thank u..
Q2 / A solid steel [G= 80 GPa] shaft of variable diameter is subjected to the torques shown in Figure. The diameter of the shaft in segments (1) and (3) is 50 mm, and the diameter of the shaft in segment (2) is 80 mm. The bearings shown allow the shaft to turn freely. (a) Determine the maximum shear stress in the compound shaft. (b) Determine the rotation angles of pulleys B,C and D with respect to pulley A. 500 N-m 4.500 N-m (1) 2,800 N-m 1,200 N-m (3) 0.70 m 1.80 m 0.70 m
-10 108 (mm) Figure 5.41 5.21 Determine the St Venant torsion constant for the thin tapered section in Fig. 5.41. Hence derive an expression for the shear stress acting along the longer edges in terms of the torque T when the thickness 10 st s 1. If T = 15 Nm estimate the position and magnitude of the maximum shear stress from a consideration of contours of constant shear stress