A circular tube is subjected to torsion by torques T applied at the ends. The bar is 0.75 m long and the inside and outside diameter are 35 mm and 46 mm respectively. It is determined by measurement that the angle of twist is 3.20 degrees when the torque is 600 N-m. (a) Calculate the maximum shear stress in the tube. (b) Calculate the shear modulus of elasticity. (c) Calculate the maximum shear strain in radians.

A circular tube is subjected to torsion by torques T applied at the ends. The bar is 0.75 m long and the inside and outside diameter are 35 mm and 46 mm respectively. It is determined by measurement that the angle of twist is 3.20 degrees when the torque is 600 N-m. (a) Calculate the maximum shear stress in the tube. (b) Calculate the shear modulus of elasticity. (c) Calculate the maximum shear strain in radians.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The tube has a length of 2 m and is made of the material with the properties provided in the following figure. (a) Determine the torque needed to just cause the maximum strain to reach 0.015. (b) What is the permanent angle of twist of the tube when this torque is removed?
A hollow steel tube used in a roof structure has an outer diameter, di = 104 mm and inner diameter, d2 = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MРа.
A thin tube of uniform thickness 5 mm and square cross section, shown below, is subject to a torque of 1500 N·m. The shear modulus of the material is 80 GPa. What will be the angle of twist per length (in unit: rad/m)? 50 mm 50 mm
B4 The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 Nm and an axial tensile force of 2 kN. Find: 500 Nm 500 Nm A 2kN 2kN (a) the tensile stress in the concrete;
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= 418.16 Use Hooke's Law to calculate the shear modulus of the specimen. answer: MPa G = i MPa
Two thin-walled aluminum tubes will be used to support a torque and they have same cross- section areas. One is rectangular cross section (7 x 4 in) and the other one is circular cross section (r = 3.5 in). The wall thickness r for both is constant 0.25 in. Find the ratio of average shear stress (rectangular to circular). +0
Answer by step of mechanical deformable bodies thank u..
-10 108 (mm) Figure 5.41 5.21 Determine the St Venant torsion constant for the thin tapered section in Fig. 5.41. Hence derive an expression for the shear stress acting along the longer edges in terms of the torque T when the thickness 10 st s 1. If T = 15 Nm estimate the position and magnitude of the maximum shear stress from a consideration of contours of constant shear stress
A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength of 240 MPa and endurance limit in reversed bending is 160 MPa. According to the Soderberg principle, the area of cross-section in mm2 of the bar for a factor of safety of 2 is
A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength of 240 MPa and endurance limit in reversed bending is 160 MPa. According to the Soderberg principle, the area of cross-section in mm? of the bar for a factor of safety of 2 is
A cylindrical rod of diameter 10 mm and length 1.0 m is fixed at one end. The other end is twisted by an angle of 10o by applying a torque. If the maximum shear strain in the rod is p×10-3 , then what is the value of p?