3.20 Determine the moment about the origin O of the force F = 4i + 10j + 6k that acts at a point A. Assume that the position vector of A is (a) r = 2i − 3j + 4k, (b) r = 2i + 6j + 3k, (c) r = 2i + 5j + 6k. 3.4 A 300-N force is applied at A as shown. Determine (a) the moment of the 300-N force about D, (b) the smallest force applied at B that creates the same moment about D. Answer 200 mm 25° 300 N A 100 mm- 200 mm D 125 mm C B

3.20 Determine the moment about the origin O of the force F = 4i + 10j + 6k that acts at a point A. Assume that the position vector of A is (a) r = 2i − 3j + 4k, (b) r = 2i + 6j + 3k, (c) r = 2i + 5j + 6k. 3.4 A 300-N force is applied at A as shown. Determine (a) the moment of the 300-N force about D, (b) the smallest force applied at B that creates the same moment about D. Answer 200 mm 25° 300 N A 100 mm- 200 mm D 125 mm C B

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A P KN Refer to the figure. d₁ 0.9 m Force P is 60 kN and each force Q is 125 kN. Q KN B Add your answer Integer, decimal, or E notation allowed Q KN The diameter d₁ = 30 mm and diameter d₂ = 50 mm. d₂ 1.2 m What is the normal stress in rod BC in MPa? Round to the nearest integer and enter the magnitude only. C
P KN Refer to the figure. d₁ 0.9 m Force P is 60 kN and each force Q is 125 kN. Q KN Add your answer Integer, decimal, or E notation allowed Q KN The diameter d₁ = 30 mm and diameter d₂ = 50 mm. B d₂ 1.2 m What is the normal stress in rod AB in MPa? Round to the nearest integer and enter the magnitude only. C Gi
Question 1 A ferromagnetic core with a relative permeability of 1500 is shown in Figure 2. The dimensions are as shown in the diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.070 and 0.020 cm, respectively. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 400 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is a) the flux in each of the left, center, and right legs of the core? b) the flux density in each air gap? 7 cm ст ст 30 cm 30 cm 7 cm 400 turns 0.05 cm 30 cm 0.07 cm 7 cm Core depth = 7 cm Figure 2
A solenoid similar to the figure below, has a core made of caststeel (refer to the figure on the next slide). It has a cross-sectional area of 4cm2 and a mean length of 20cm. The coil has 100turns, and the coil current is 3.2A. Find the following:a)magnetomotive force, mmfb)magnetic field intensity, Hc)flux density, B (with graph)
The relative permeability of a certain silicon steel is 4500. A certain magnetic loop consist of a silicon steel of 10 cm square, 20cm long and an airgap of ¼ cm. What is the reluctance of the magnetic circuit? PLEASE PROVIDE SOLUTIONS. a. 2.54 x 10-2 b. 6.44 x 10-3 c. 6.44 x 10-4 d. 2.54 x 10-3
A DC current I flows in a long solenoidwith n coil-turns per unit length. Thecore is made of iron with permeability µ , and has a cross section area S.Determine the force acting on the coreif it is withdrawn to the position shownin figure.
A ten-turn solenoid has a ferromagnetic core with a relative permeability of 10,000. The length of the solenoid is l=10 cm and its cross section area is A=1 cm2. The amount of current driving the solenoid is 0.1 A. Determine the magnetic flux density B in the core. Provide your answer in milli Tesla. Round off to your answer to one decimal.
A solenoid similar to the figure below, has a core made of cast steel (refer to the figure on the next slide). It has a cross-sectional area of 4cm2 and a mean length of 20cm. The coil has 100turns, and the coil current is 3.2A. Find the following: a)magnetomotive force, mmf b)magnetic field intensity, H c)flux density, B
3.12 A carbon brush used to conduct current from the commutator of a DC generator has a length of 4 in. It must conduct a current of 400 A with a voltage drop not exceeding 2 V. Determine the cross-sectional area of this carbon brush. 3.13 Early DC machines use brass brushes instead of carbon brushes. The com- mutator bars do not last very long since brass is a rather hard metal. If a brass brush of the dimensions determined in problem 3.12 is used instead to conduct the same current, determine the voltage drop.
. An iron core has a cross-sectional area of 10-3 square meter and mean circumference of 1 meter. The relative permeability of the material is 500 and the number of turns is 200. Determine the current required to set up a flux of 0.001 weber. a. 7.54 A b. 7.96 A c. 8.19 A d. 8.47 A
Question: can you help me pls Assuming the magnetic permeability of the core as infinite in the magnetic circuit given in the figure, find each self- inductance and common inductance in terms of A1, A2, g1 and g2. 92 N2 iz the area of the shaded area A1, the area of the other areas A2
A freight elevator weighing 5000kg is to be lifted 20 meters in 3 minutes. Calculate the horsepower of the motor required to do the job. A magnetic circuit has a flux of .75 Webers. The magnetic force (Fm) applied to the circuit is 550 Amp-turns. What is the reluctance (Rm) of the magnetic circuit? A magnetic circuit with a reluctance (Rm) of 1500 AT/Wb has a flux of 430 mWb. What is the force magnetic (Fm) of this circuit? Hint: Rm = Fm/flux