3.3-2 When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure) with a bit of diameter d= 4.0 mm. (a) If the resisting torque supplied by the table leg is equal to 0.3 N-m, what is the maximum shear stress in the drill bit? (b) If the shear modulus of clasticity of the steel is G= 75 GPa, what is the rate of twist of the drill bit (degrees per meter)?

3.3-2 When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure) with a bit of diameter d= 4.0 mm. (a) If the resisting torque supplied by the table leg is equal to 0.3 N-m, what is the maximum shear stress in the drill bit? (b) If the shear modulus of clasticity of the steel is G= 75 GPa, what is the rate of twist of the drill bit (degrees per meter)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2. A circular aluminum tube subjected to pure torsion by torques T (see figure 2) has an outer radius 12 equal to 1.5 times the inner radius ₁. (a) If the maximum shear strain in the tube is measured as 400x106 rad, what is the shear strain y at the inner surface? (b) If the maximum allowable rate of twist is 0.125 degrees per meter and the maximum shear strain is to be kept at 400x105 rad by adjusting the torque T, what is the minimum required outer radius (12) min? T Figure 2: cylindrical shaft
1 of 1 T -1.5m Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 500N.m as in figure. Take shear modulus as 80MPA Determine: A- The Max. shearing stress introduced by the shaft. B- The angle of twist in degree. C- The shear strain in the shaft. D- The Min. Shearing stress in the shaft
A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The allowable shear stress in the steel is 40 MPa. G=70 GA (a) What is the required diameter d of the shaft if it is operated at 1500 rpm? (b) What is the required diameter d if it is operated at 3000 rpm? (c) If the length of the shaft from the motor to the gear is 1 m, what are the angles of twist for the two speeds of rotation? Motor Motor
A circular aluminum tube subjected to pure torsion by torques T (see figure 2) has an outer radius r2 equal to 1.5 times the inner radius r1 (a)If the maximum shear strain in the tube is measured as 400x10 to the power 6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist is 0.125 degrees per meter and the maximum shear strain is to be kept at 100x10 to the power 6 rad by adjusting the torque T, what is the minimum required outee radius (r2) min ?
Mechanics of deformable bodies
= 1.3-18 A stepped shaft ABC consisting of two solid，circular segments is subjected to uniformly distrib uted torque i，acting over segment 1 and concentrated torqueT₂applied at C，as shown in the figure。Seg ment 1 of the shaft has a diameter ofd₁= 57 mm and length ofL₁= 0.75 m; segment 2 has a diameterd₂= 44 mm and lengthL₂= 0.5 m。Torque intensity1₁3100 N m / m andT₂= 1100 N·m。（a）Find reaction torque T at support A.（b）Find the internal torque T（x）at two locations：
The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at point E as in the figure andIt is subjected to a force of 800 N, a torque of 45 N.m and a moment of 300 N.m, applied from the other end of the pipe as in the figure.if left, it will occur at point A; (f) Find the aspect of the plane of maximum shear stress. Note: Point A is on the top and outer surface of the steel pipe. The line AB is parallel to the z-axis andpasses through the centre..
The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c ). If the allowable shear stress of the shaft is 81kPa (i) Determine the maximum torque T that can be transmitted by the shaft. (ii) What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? (iii) Sketch the shear-stress distribution along a radial line in each case. T T' Figure Q2(c)
A 3 m long steel angle shown in the figure has a section thickness of 12.7 mm and a cross sectional area of 4350 mm². Since tem = 50 MPa and G = 77.2 GPa, find the maximum applicable torque T.
A hollow steel shaft used in a construction auger has outer diameter d2 = 7.8 in. and inner diameter d1 = 5.5 in. (see figure). The steel has shear modulus of elasticity G = 11.5 x 10^6 psi. For an applied torque of 175 k-in. , determine the following quantities:a.) Shear stess T2 at the outer surface of the shaftb.) Shear stress T1 at the inner surfacec.) rate of twist Θ (degrees per unit of length)
Read the question carefully and give me all right solutions. Internal torque at rod 1 (kip-ft) Magnitude of shear at rod 2 & 3(ksi) Rotation angle at rod 1 (deg) Rotation angle at flange C (deg)
A hollow aluminum tube used is a roof structure has an outside diameter d2=70mm and inside diameter d1= 50mm. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.) If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist in degrees when the max shear stress is 50MPa? b.) What diameter 'd' is required for a solid shaft to resist the same torque with the same maximum stress?