3.14 The following data refer to an axial flow blower with a single stage: Mass flow rate=0.75 kg/s Rotor tip and hub diameters= 24 cm and 16 cm Rotational speed = 3500 rpm As the air flows through the rotor, it turns through an angle of 22° away from the axial direction. Assuming standard atmospheric conditions and that the axial velocity is a constant, compute the degree of reaction and power input to the blower. Also, find the utilization factor. Inlet absolute velocity is purely axial.

3.14 The following data refer to an axial flow blower with a single stage: Mass flow rate=0.75 kg/s Rotor tip and hub diameters= 24 cm and 16 cm Rotational speed = 3500 rpm As the air flows through the rotor, it turns through an angle of 22° away from the axial direction. Assuming standard atmospheric conditions and that the axial velocity is a constant, compute the degree of reaction and power input to the blower. Also, find the utilization factor. Inlet absolute velocity is purely axial.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q. A boiler is equipped with a chimney of 30 m height. The ambient temperature is 25°C. The temperature of flue gases passing through the chimney is 300°C. If the air flow is 20 kg per kg of fuel burnt, find the draught produced and the velocity of flue gases through the chimney when 50% of the theoretical draught is lost in friction.
A double-acting cylinder has a plunger of 10 cm in diameter. The diameter ratio between the plunger and the stem is 5. This cylinder is connected to a compressed air network at the pressure of 2 MPa and performs 15 cycles per minute. Assuming a friction force equal to 10% of the theoretical one, calculate: a) The force exerted by the stem in the advance race and the one exerted in the return race. b) The stroke length if the air flow, measured under normal conditions, is 583 l/min. c) What would be the section of a single-acting cylinder, working with traction, that would provide the same flow?
67. A turbine is located 100 m below the surface of a lake. The discharge pipe has an elevation of 5 m from the turbine centerline. The head developed by the turbine is 81.5 m. Pressure at the discharge pipe is 15 psig. Find flow velocity and the power developed by the turbine. Ignore frictional losses and use D; = 4 m. [Ans.: V4 = 7.62 m/s, 76.5 MW].
An 8 m/s wind enters a wind turbine rotor with a diameter of 36 m. Assume the air density 1.2 kg/m3 Calculate: The power of incoming wind, The maximum power extracted by the wind turbine, If the gearbox, generator and electrical transmission and processing efficiencies are 0.85, 0.96 and 0.95, respectively, what is the turbine effective converted power
Design a rocket nozzle, knowing that you have a chamber pressure of 6.28 MPa, mass flow rate of 1.23, and temperature of 825K.
A wind turbine testing laboratory provided the following results results: • Speed in the feed section = VA • Speed in the discharge section = VD • Feed (cross-section) area = A • Static pressure in the supply section = PA • Temperature in the feed section = T • Static pressure in the discharge section = Patm Estimate the reaction (strength) that the wind turbine will exert on the support with the information you collected in the tests. Take on that the air behaves like a perfect gas.
#3 fluid machineries. will upvote anyone who will answer, please make complete solution and corrects units. Thanks
Q4 see photo provided.
Please Answer all my Question .. Please help me , I don't want plagiarism.
The following data refer to a rocket engine, Velocity of jet = 1600 m/s Speed ratio = 0.7 %3D Fuel flow rate = 1kg/s Oxidizer flow rate = 4 kg/s Heat of reaction per kg of exhaust gases = %3D 2500 kJ/kg. impulse, propulsive efficiency, propulsive Determine, the thrust produced, specific power, thermal efficiency and overall efficiency of rocket enqine,
Example 4.9 Compute the required motor capacity needed for the FD fan under the following conditions: : 10 tonnes/h : C 78.0, H 3.0, O 3.0, S 1.0, M 7.0, A 8.0 : 30% Coal rate Coal analysis Excess air Plenum chamber pressure Mechanical efficiency of the fan Room temperature 180 mm water gauge 60% : 30 °C
Provide Solutions Subject : Fluid Machinery