The single stage, axial flow turbomachine shown in figure 3 involves water flow at a volumetric flowrate of 14m³/s .The rotor revolves at 600 rpm. The inner and outer radial of the annular Flow path throug the stage are 0.46 and 0.61 m, and B2=25°. The flow entering the rotor row and leaving the stator row is axial viewed from the stationary casing. Is this device a turbuine or a pump? Estimate the amount of power transferred to or from the fluid. [M Rotor ,Stator Q=14 m³ /S U2 fo=0.61 m 0.46 m 600 rpm

The single stage, axial flow turbomachine shown in figure 3 involves water flow at a volumetric flowrate of 14m³/s .The rotor revolves at 600 rpm. The inner and outer radial of the annular Flow path throug the stage are 0.46 and 0.61 m, and B2=25°. The flow entering the rotor row and leaving the stator row is axial viewed from the stationary casing. Is this device a turbuine or a pump? Estimate the amount of power transferred to or from the fluid. [M Rotor ,Stator Q=14 m³ /S U2 fo=0.61 m 0.46 m 600 rpm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Kindly explain this, Thank you very much
Problem 2) A pressure of 10 kPa gage is applied to the surface of water in a tank. There is an outlet 0.5m below the surface of the water. What is the velocity of the water exiting the outlet into the air? You may assume that the velocity of the water leaving the outlet is much much faster than the velocity of the water level dropping inside the tank. 10 kPa gage 0.5 m
1. One pound of air per second with an initial temperature of 180°F is allowed to expand without flow (closed system) from a pressure of 120 to 20 psia. Find the work in hp if the process is 1. pv = c 2. pvk = c 3. pv1.5 = c
A 3-bladed wind turbine with 250 kW generator has diameter of 50 m and tower height of 60 m. It is designed to have Cp of 0.25 at wind speed of 12 m/s when regulation starts. The cut-in and furling Speeds for the machine are 5 m/s and 20 m/s respectively. Mechanical and electrical efficiencies are 90 % and 95 %. By assuming the density of air as 1.225 kg/m3. Calculatea. What is power developed by the rotor at 12 m/s when regulation starts? b. If the tip-speed ratio at this wind speed is 4.2, then what is the rpm of the rotor? c. Calculate the actual torque developed. d. Calculate the maximum possible annual power output.
However a gas does a differential amount of work δWb as it forces the piston to move by a differential amount ds.
6.5-7
An air compressor absorbs 1000 kg of air per hour at a pressure of 100 kPa and 500 kPait presses on the pressure. Specific volume of air at compressor Inlet 0.8 m3/ kg, at Exit0.2 m3/ kg dir. The internal energy of the air at the outlet is 100 kJ/kg more than at the inlet.60 000 kJ/h heat transfer occurs from the compressor to the air. Kinetic and potential energyfind the power needed to operate the compressor, neglecting its changes.
A pump is supplying water at the rate of 4ft^3/s it lifts water to a height of 15ft. Determinte the power that the water is being delivered to by the pump (hp). If the pump has 80% efficiency , find the power that needs to be supplied to the pump (hp)
A water pump increases the water pressure from 15 psia to 90 psia. Determine the powerinput required (hp), to pump 2 ft3/s of water. Neglect potential, heat, kinetic energychanges.
Find an expression for the rate of change of the mass of water in the tank.
PLEASE ANSWER QUICKLY
Water is being pumped from an atmospheric source on the ground at the rate of 200 liter/minute to a pressurized tank on top of an office building through a constant diameter pipe. The discharge to the pressurized tank is 20 meters off the ground and the tank has a gauge pressure of 5 bar. Ignoring frictional losses, determine the a)power the pump must supply the fluid in W (Correct Answer is 2321 W) By performing an energy balance around the pump and ignoring friction and any changes in height between the inlet and outlet of the pump determine the: b) increase in pressure across the pump in psi (Correct Answer is 101 psi)