3.1 3.2 Determine the location of the centroid for the cross-section shown below and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate its distance from the selected origin. (Start your calculations be setting an origin from the bottom, left-most point on the cross-section). Calculate the second moments of areas about the centroidal axes for the beam cross- section. 60 mm 10 mm 10 mm 100 mm 40 mm 10 mm ビュ

3.1 3.2 Determine the location of the centroid for the cross-section shown below and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate its distance from the selected origin. (Start your calculations be setting an origin from the bottom, left-most point on the cross-section). Calculate the second moments of areas about the centroidal axes for the beam cross- section. 60 mm 10 mm 10 mm 100 mm 40 mm 10 mm ビュ

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.38P: The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the...

See similar textbooks

Similar questions

Compute Ix and Iy for the region shown.
For the region shown, Ixy=320103mm4 and Iuv=0. Compute the distance d between the y- and v-axes. (Note: The result is independent of x. )
Determine Ix for the triangular region shown.
The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the catenary is the shape of a cable suspended between two points). Locate the y-coordinate 0f the centroid of the catenary by numerical integration using x=25ft.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
The L806010-mm structural angle has the following cross-sectional properties: Ix=0.808106mm4,Iy=0.388106mm4, and I2=0.213106mm4, where I2 is a centroidal principal moment of inertia. Assuming that Ixy is negative, compute (a) I1 (the other centroidal principal moment of inertia); and (b) the principal directions at the centroid.
Find the centroid of the truncated parabolic complement by integration.
Determine Iu for the inverted T-section shown. Note that the section is symmetric about the y-axis.
Verify the centroidal z-coordinate of the pyramid shown in Table 8.3 by integration.
3.1 Determine the location of the centroid for the cross-section shown below and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate its distance from the selected origin. (Start your calculations be setting an origin from the bottom, left-most point on the cross-section). 3.2 Calculate the second moments of areas about the centroidal axes for the beam cross- section. 60 mm 10 mm y 10 mm 100 mm 10 mm 40 mm
Determine the locationof the centroid for the cross-section shown below and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate its distance from the selected origin. (Start your calculations be setting an origin from the bottom, left-most point on the cross-section). 2 Calculate the second moments of areas about the centroidal axes for the beam cross- section. 60 mm |10 mm 10 mm 100 mm 10 mm 40 mm
3.1 Determine the location of the centroid for the cross-section shown below and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate its distance from the selected origin. (Start your calculations be setting an origin at the bottom, left-most point on the cross-section). 3.2 Calculate the second moments of areas about the centroidal axes for the beam cross- section. 100 mm y z 10 mm 10 mm 10 mm Figure 3: Cross-section ww OSt 100 mm