3. Write instruction codes to to initialize the IO ports for the configuration below BINARY INPUTS RC4 RC3 RC1 RCO PIC16F877 RB7 RBO RC5 RC6 RC2 (PWM) GND MOTOR MOTOR DRIVER

Q: 1. Convert the Hexadecimal number (A493.C4)16 to decimal number.

A: From the Hexadecimal to Decimal convertion

Q: Calculate the offset for the physical address 00062 H and segment address FFFFH,

A: physical address is calculated by shifting the segment address (16-bit) left 4 times and adding it…

Q: emory organization and command processing technique architectures used in 80x51 microcontrollers are…

A: Memory organisation and command processing technique architectures  used in 8051 are Harward and…

Q: What are the two primary categories of output circuits in TTL?

A:

Q: 25 A timer is set in PWM mode 1 Peripheral clock = 48MHZ Prescaler = 8 %3D Value in TGRA = 0XD6D8…

A: According to the question, we need to calculate the frequency of the generated signal for PWM mode…

Q: analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The…

A: We need to find out number of bits per sample , first we will find out the number of level then we…

Q: Make pin diagram for 16x2 LCD mention purpose of each pin

A: The 16x2 LCD have the 16 pins and it display in two line with 16 characters. So we can display 32…

Q: The following ASCII code 0000110 represents

A:

Q: clock cycles form one bus cycle. ROM can be classified into Dynamic ROM and Static ROM. Select one:…

A: 4 clock cycles are needed to form 1 bus cycle       RAM is classified into dynamic RAM and static…

Q: List 8051's primary characteristics. Explain the basic microcontroller block diagram using a clean…

A: The 8051 Microcontroller is one of the basic types of microcontrollers, designed by Intel in 1980s.…

Q: An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz.…

A: We need to find out the number of bits per sample for given ADC . First we will find out number…

Q: An analog signal is to be coded by an ADC.  The signal contains significant frequencies up to 6MHz.…

A: We need to find out number of bits per sample, first we will find out the number of level then we…

Q: De fine time constant (I) for (R-L) cct.

A: The time constant (τ) for an RL (resistor-inductor) circuit is calculated using the…

Q: You are developing a distance measuring system using an analog infrared sensor The response curve of…

A: ADC converts the analog input voltage into digital output. The output will be a number in the range…

Q: Total Number of active low pins in IC74LS138? Options A-7 B-8 C-9 D-10

A: The answer is D-10 because For an active high pin, you connect it to HIGH voltage . the Pin having a…

Q: Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be…

A: Given that : 6 bit ADC range (0-59) to Find Resolution :

Q: Section 2-8 Hexadecimal Numbers 37. Convert each hexadecimal number to binary: (a) 4616 (e) FA 16…

A: Hexadecimal is a base-16 number system that uses 16 symbols to represent values. The symbols include…

Q: Convert the OCTAL NUMBER 7715. 6 57 5 to decimal number (show the steps in paper

A: Given, Octal number=7715.6578

Q: Vrite data flow verilog code for half adder.

A:

Q: Turn even LEDS with one switch and odd LEDS with another switch for RB port of a PIC16F84A. Write a…

A: Aim: To Write a program in assembly language for PIC16F84A which would Turn even LEDs with one…

Q: Logic "1" (HIGH) Clock Pulse trailing-edge J FF1 CLK K Ch al J FF2 CLK K at Cir FF3 CLK K Q at J FF4…

A:

Q: Convert the following numbers: 10101010 binary to hexadecimal Hexadecimal number BEAD to decimal…

A: As per the guidelines, the first 3 sub-parts has been solved in the following section:

Q: Draw 8259A interfacing connections with 8086 at the address 0744H.

A: The 8259A interfacing connection with 8086 at address 0744h is shown below:

Q: Oa. PORTA O b. PORTB O c. PORTC and PORTD all of above O d.

A:

Q: Differentiate/Compare the 78xx (and the 79xx) series and the LM317 (and LM337) IC with LDOs (low…

A: According to the question, Differentiate/Compare the 78xx (and the 79xx) series and the LM317 (and…

Q: The button is on the 3rd bit of PORTC. When the button is pressed, turn on all leds on PORTD. ORG…

A: Microcontroller (PIC16F877A):…

Q: Discuss the evolution of microchip technology and its impact on the field of electronics.

A: We need to discuss the evolution of microchip technology and its impact on the field of electronics.

Q: Application of Flash Type ADC

A: The explanation is as follows.

Q: 1. Determine the corresponding product term per row

A: For the given programmable Array Logic the value of each product term need to be obtained.

Q: Identify the circuit function below and draw the waveform timing diagram

A: The circuit diagram is shown below,

Q: TTL family IC 74ALS86 belongs to Average Level Semiconductor TTL Advanced Low power Schottky TTL…

A: Solution: TTL means transistor transistor logic. The features of the TTL family are only 10 mW power…

Q: Q4) Figure below shows a typical clock-oscillator circuit using a (555 timer) and a (J-K flip-flop).…

A:

Q: Discuss the evolution of microchips and their significance in modern electronics.

A: Discuss the evolution of microchips and their significance in modern electronics.

Q: Do Y. So EN Parity generator Demultiplexer Decodor 身

A:

Q: 1-Write microprocessor program using mnemonics to add two numbers 08 and 06. 2-Write the object code…

A: Since you have asked multiple question I will answer the first question for you. MOV RD , RS  Here…

Q: Convert -7.45 decimal number into IEEE754 Standard?

A: The format for IEEE754 standard is given as: and the exp bias for the IEEE754 standard is 7.

Q: An 8085 assembly language program is given below. Line 1: MVI A, B5H 2: MVI B, OEH 3: XRI 69H 4: ADD…

A: Given Assembly language program. We have to find the content of accumulator after the execution of…

Q: in Intel 8086 microprocessor, the memory address for the code segment 771F h and offset 3584 h is O…

A: memory address = code segment + offset  1. Given code segment = 771F and offset = 3584 H  code…

Q: What is thte type of signal used in television? a. R3E b. B8E c. F3E c. C3F

A: Choose the correct option What is the type of signal used in television?