3. The box beam supports the concentrated loads 2P and P. Compute the maximum allowable value of P if the working stresses in bending and shear are ow = 1200 psi and tw = 150 psi, respectively. | 2P P 8 in. B D A |E 8 in. 10 in. 5 ft - - 5 ft 5 ft- 6 in. 0.5P 2.5P

3. The box beam supports the concentrated loads 2P and P. Compute the maximum allowable value of P if the working stresses in bending and shear are ow = 1200 psi and tw = 150 psi, respectively. | 2P P 8 in. B D A |E 8 in. 10 in. 5 ft - - 5 ft 5 ft- 6 in. 0.5P 2.5P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the loads of the figure to be axially applied at sections B, C, and D to the concrete structure supported at A. IW E F P G 5 kN 5 kN A Determine P in kN when member BC is 24 mm in diameter, the axial stress in section F is 588 MPa, and W 309822 N. = 10 kN C 10 kN Rigid -bearing plates
Calculate the rod forces FH, EH, and EG of the truss system for the given loading condition using the section method. State whether the rod forces are tensile or compressive.
The intensity of the triangular load carried by the T-section varies from zero at the free end to wo at the support. Find the maximum safe value of wo given that the working stresses are 4000 psi in tension and 10 000 psi in compression.
Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section. The following Inte Av = 9K Bv = 11K location of centroid = 3.56" above X-Ref Shear diagram Moment diagram 1" x 10" steel plate 1" x 8" steel plate X-reference A 6' 8K 12' 24' 12K 6' B of your work is accurate. Yo ment Mmax = 66K' Vmax 11K Moment of Inertia = 218 inª
anwser 2nd part
Problem # 3: The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b=0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 0.80 in 3 ft с VO A 5 ft- + B 6 ft- D 2750 lb 3.75 in 3.75 in Strut AB - Beam CD (b X h) Bolt (dmin) -0.50 in
P2
What is the maximum absolute shear for the following beam and load group? Use L = 21, a = 3, b = 2, P₁ = 4, P₂ = 2, and P3 = 3. × 6.76 L P3 P2 P₁ P₂ P² a b
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-Section and a Channel (C-Section) fastened together by 16mmØ bolts, equally spaced from the center of the section, with shearing capacity t=100 MPa, for bearing os = 220 MPa for rivets in single shear and os = 280 MPa for rivets in double shear. E=200GPA for all materials. 8 KN 15 KN/m 12 KN/m 2m 3m 3m 2m Properties of T-Section Br = 180 mm Tf= 16 mm Tw = 12 mm D = 210 mm Properties of C-Section B = 105 mm T = 12 mm Tw = 12 mm D = 210 mm
Determine the shearing stress at the neutral axis. (in Psi). Note: include the negative sign in the answer box, if the stress is in compression. L1 = 4 ft, L2 =8 ft, L3 = 4 ft. W = 60 lb/ft, b = 6 inches, d = 6 inches %3D 2d W L1 L2 L3- b.
The spreader beam AB is used to slowly lift the 3000-lb pipe that is centrally located on the straps at C and D. If the beam is a W12 * 45, determine if it cansafely support the load. The allowable bending stress is sallow = 22 ksi and the allowable shear stress is tallow = 12 ksi.
2 A simply supported beam has a dimension of 300mmw x 600mmh has a span of 6m. it has a superimposed load of 30KN/m and live load of 50KN. It has a specified concrete strength of 28MPa and yield strength of 420MPa. Distance of centroid steel area to outermost fiber is 60mm. a. What is the maximum moment of the beam? b. What is the required tension steel area? Use et = 0.004