3. In the circuit below, the op-amp is ideal, except for an input bias current |Ib| = 1 nA.Further, RF = 10K, R1 = 100 0 and C = 0.1 µF. The switch is opened at t = 0. What isthe output voltage after 5 seconds?RFR1VoSwitchC* Tip: For t 2 0, the voltage across the capacitor is v vc= (+IbAt)/C

The ideal OP-Amp (operational Amplifier) is the type with infinite - open loop gain , bandwidth,…

3. In the circuit below, the op-amp is ideal, except for an input bias current |Ib| = 1 nA. Further, RF = 10K, R1 = 100 Q and C = 0.1 µF. The switch is opened at t = 0. What is %3D the output voltage after 5 seconds? RF R1 Vo Switch * Tip: For t2 0, the voltage across the capacitor is v= vc = (+IbAt)/C %3D

3. In the circuit below, the op-amp is ideal, except for an input bias current |Ib| = 1 nA. Further, RF = 10K, R1 = 100 Q and C = 0.1 µF. The switch is opened at t = 0. What is %3D the output voltage after 5 seconds? RF R1 Vo Switch * Tip: For t2 0, the voltage across the capacitor is v= vc = (+IbAt)/C %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If I have an input sine wave in a peak detector circuit I know the output the the first op amp (that will feed back into the negative terminal) should be a little larger than the input (this is why you add a second op amp). I'm not understanding it graphically. Splitting up the circuit say you have the first op amp and the diode (no capacitor or second op amp). the output should be only the positive part of sine wave, and the amplitude will be the amplitude input minus .6V from the diode drop, right? Then adding the capacitor it keeps the same amplitude but makes more DC. with the second op amp this makes it so the capacitor doesn't discharge (which is what keeps the voltage proper up I think?) With my logic here, the voltage feeding back into the first op amp negative terminal is the voltage input, minus a diode drop. So Vin > V- (voltage feeding back into the negative terminal). Which I'm pretty sure V- is supposed to be larger. So I think I'm misunderstand something here. Please…
1. Use the figure below for the following questions. R = 10N and V is a 5V DC source that can provide a maximum of 1 mA of current. The op-amp is ideal. Vin R Vo What is V, in volts? Enter answer here 2. What is Iut in miliamps?
3ZF The typical value of the out impedance of an op-amp is a.between 100 Ohms to little less than 1 KOhms b.less than 100 Ohms c.at least 10 percent of the input impedance d.equivalent to short circuit
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator wilh R = 10OKOhms, C = 10UF and a sine wave inpul waveform, the output waveform is a cosine waveform. %3D ii. For an op-amp integrator with R = 100KOhms, C = 10uF and a triangular input waveform, the output waveform is a square wave. iii. For an op-amp integrator with R- 100KOhms, C =10uF and a sine wave input waveform, the output waveform is a sawtooth waveform. v. For an op-amp integrator with R10OKOhms. C lCuF and a square wave input waveform, the output waveform is a triangular waveferm.
a) For an opamp, the input bias current Ib =60uA and the input offset current lio= 10uA Find the input base currents and In b) Design an opamp circuit with the following output: Vo = - Vin/4 + 2 For the circuit given below Given :Vin-0.2V, Vsat= 12V D Identify (name) the circuit (stage 1 and 2) O Find the output voltage Vo and the current through the load 4ka 0 Find Vo if the resistor 2kn opens 10 k Stage Stage 2 Vo Vin
Q1) Using the following input waveform shown in Figure 1, sketch the corresponding output waveform for each op amp circuit shown in Figure 1(a through d). Assume ideal op amp behavior. 30 441 wwwww 25 AG 10 pF 100 k www (6) 1,0 330 www 10 LQ www 51.02 540 M 530 www 10 KO or
Assuming an ideal· op-amp's saturation voltage- UsSAT = +15V. For the- circuit in Figure · if u = 3V, the output voltage of op-amp is (404) i 10
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be:
. For the combinational op-amp circuit A. Identify the connection/application of each op-amp: A1, A2, A3 and A4. B. Find V01, V02, V03, and V0.
0.2 Design inverting circuits. an op-amp circuit to produce the output Vo= 8Vi, using both inverting and non 19
What configuration of the op amp is used to couple one stage of a circuit to another by its input and output impedance characteristics?
From the figure , write note voltage equations, one for each input terminal of the op amp The expression for the load current ( iL) can be written as a function of the input voltage (Vin) and the load voltage (VL) IL =A(Vin) + B(VL) b.1 What is the expression for A? b.2 What should be the condition for R1 R2 R3 R4 so that B is zero? (NB this will make( iL) depend only on Vin and not on RL)