i need the answer quickly 3. Given the pulley system with block A and a pull down motion at pointF at 3 m/s, determine the following:(a) Datum. You may write the datum directly on the provided diagramor you may redraw the diagram and indicate the datum.(b) Positive directions of block A and point F.(c) Appropriate labels that will be used in formulating an equation(eg. Sa, Sb, La, Lb, etc) You may write the labels directly on theprovided diagram or you may redraw the diagram and indicate theAlabels.(d) Equation for the total length of cord/s (if applicable).(e) Resulting equation after differentiating the equation in (c) withrespect to time.(f) Velocity (magnitude and direction) of block A.vf = 3 m/sIf u don't know all parts please skipIf all parts doing I surely gives u 6 likes in one question

(a) Considered the diagram as shown below for the datum.

Answered: 3. Given the pulley system with block A…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please
Find the magnatidue of VB(ft/s): Find the angle of VB(degrees)
Gear A rotates CW as shown and drives the rack F through gears B, C, D, and E. What is the direction of motion of rack F that is free to move vertically only? B C A D E F Don't use chatgpt, Solve the problem in handwritten format.
writing in paper please
Consider the hanging crane structure in Figure 1. Write the equations of motion describing the motion of the cart and the payload by using Newton's 2nd Law. The mass of the cart is M, the mass of the payload is m, the mass-less rigid connector has length L, and the friction is modeled as Fb(t) = -bx_ where x is the distance traveled by the cart. Hint: Use normal and tangential coordinate systems.
7. In the pulley system shown below, the cylinder moves upward at a velocity of 6.7 ft/s as the cable is pulled by the winch motor. Answer the following questions. a. Use the figure below to label the horizontal and vertical datums. Include all relevant distances needed to evaluate the pulley system. C b. How many individual cables are used in this pulley system? Explain how the number of cables is related to how many equations are needed to describe the motion of the system. Magnitude rounded to 3 sig. fig. B C. What is the velocity of Point A? Show your work. Units Direction (right or left)
For the 3Bar Inverted Crank Slider shown, the following data is given: R2 = a, R₁ =d, 02, W2, α2. απ W2 R2 02 02 R4 04 O2 and 04 are grounds. 04 R1 1. Starting with the algebraic position equation R = Au; where R is the position of the vector in the fixed frame [XY]T, A is the rotation matrix and u is the coordinates of a point on the vector in the local frame, [xy]. With R₂ = a, R₁ = d, 02, W2, and a₂ given, derive the general position, velocity, and acceleration equations in both algebraic and matrix form. Note: your answer must begin with the vector loop and continue the derivation. 2. For the 3-bar crank slider with R2 = 2 in, R₁ =10 in, 02 = 20°, w₂ = 10 rad/sec ccw, α₂ = 0 rad/sec², determine values for R4 = c, 04, Ċ, W4, C, and α. 3. What are the angular velocity and acceleration for the slider block.
How we can find OB by Trig Please I want with steps
T5
The general linkage configuration and terminology for an offset fourbar slider-crank linkage are shown in Figure below. The link lengths and the values of 02 and w2 are defined in. For the row(s) b and c, find the velocities of the pin joints A and B and the velocity of slip at the sliding joint using an analytical method. Draw the linkage to scale and label it before setting up the equations. y A 03 B Y 4 Link 3 A W2 Offset 02 04 = 90° Link 2 X 02 Slider position d TABLE P6-2 Data for Problems 6-6 to 6-7† Row Link 2 Link 3 Offset 02 02 a 1.4 4 1 45 10 2 -3 60 -12 3 8 2 -30 -15
The general linkage configuration and terminology for an offset fourbar slider-crank linkage are shown in Figure below. The link lengths and the values of 02 and w2 are defined in. For the row(s) b and c, find the velocities of the pin joints A and B and the velocity of slip at the sliding joint using an analytical method. Draw the linkage to scale and label it before setting up the equations. Link 3 Offset 04 = 90° Link 2 02 Slider position d TABLE P6-2 Data for Problems 6-6 to 6-7† Row Link 2 Link 3 Offset 02 1.4 4 1. 45 10 2 6. -3 60 -12 3 8. -30 -15
Boxes are pulled by ropes along frictionless surfaces, accelerating toward the left. All of the boxes are identical, and the accelerations of the boxes are indicated. (note that accelerations of the sets of boxes are not the same) Put a greater than symbol between letters if one is greater than the other, put an equal sign between them if they are equal. Put a space or comma between all characters. Example: D = C > A > B Rank the tension in the ropes from greatest to least.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS