3. Considering the beam loaded as shown below. Assume El - 50 000 kNm² 25KN 10k:N/m 1SKN.m A B Im Im Im lm 2m 2m 2m 2m a. What is the slope and deflection at A? b. What is the slope and deflection at B? c. What is the slope and deflection at C? d. What is the maximum deflection? e. Determine the location of the maximum deflection from the right support. Express the slope in degrees.

3. Considering the beam loaded as shown below. Assume El - 50 000 kNm² 25KN 10k:N/m 1SKN.m A B Im Im Im lm 2m 2m 2m 2m a. What is the slope and deflection at A? b. What is the slope and deflection at B? c. What is the slope and deflection at C? d. What is the maximum deflection? e. Determine the location of the maximum deflection from the right support. Express the slope in degrees.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The beam shown below is subjected to two 4 kN concentrated loads located 1.5 meters from each…

Q: 60 kN/m- 30 kN/m A Hinge B 5 m 10 m-

Q: Determine the Deflection at C. Use the Any Geometric Method (once for DIM, once for AMM, once for…

Q: For the cantilever steel beam [E = 220 GPa; I = 83 x 106 mm4), use the double-integration method to…

Q: The overhang beam shown below has a non-prismatic section. Given E = 29000 ksi, I = 3000 in¹.…

A: Given: A non prismatic overhang beam Required: Rotation at C and deflection at D using conjugate…

Q: HW 2: Determine the deflection at point C of the beam shown in Fig. below by the virtual work…

A: Given :

Q: IV- Double Integration Method 4. Determine the slope and deflection at B and the maximum deflection…

Q: Problem 41: Determine the maximum slope and maximum deflection for the beam shown in figure by…

Q: 120 kN 120 kN L-15 m El = constant E- 30 GPa The beam has a self weight of 5 kN/m in addition to the…

Q: a = 2.5 m, b = 27.3 kN/m, c = 23 kN. "a" m b kN/m BI 4 m kN 3m determine the deflection at B in mm…

A: Given b x h =150mm x 200mm I=b×h312=150×200312=108mm4E=80Gpa=80×103MpaEI=8×1012Nmm2 To Find…

Q: The intensity of the distributed load on the simply supported beam varies linearly from zero to wo =…

A: Find location of the maximum deflection if L = 7.2 feet.

Q: Use the unit load method (or Principle of Virtual Work) to determine the deflection dA in inches at…

A: EI = 28800 k-ft2

Q: Calculate the deflection at B in terms of El. Express your answer in two decimal places and do not…

A: Using Macualay's method Considering EI is in KN/m2

Q: Calculate the slope and deflection atB and E of the beam and loadings shown using conjugate beam…

Q: Q.3 Determine the slope at A and deflection at C in the beam shown below: 11KN/m 4m C 2m 10KN 3m B

A: We have to determine the slope at A and deflection at C

Q: Calculate the deflection at C in terms of El. Express your answer in two decimal places and do not…

Q: Solve the slope and deflection of the compound beam shown at point E which is located 3m to the…

A: Given: A compound beam Required: Slope and deflection at point E using conjugate beam method

Q: Determine the deflection at the end of the overhang by applying the second moment area theorem. The…

Q: For the beam and loading shown, determine the deflection under the load. E = 12 GPa, I = 110 x 106…

Q: . For the beam loaded as shown in the figure below, determine the following unknowns using any…

Q: E : 29110° Ksi I: 20 in" • Determine the vertical deflection at D 10 K lf+ D B 204 C 2 ft ト 201 21

Q: Problem 4: If the material of the beam has an allowable bending stress of Galow = 175 MPa. determine…

A: dear student as per our company guidelines i am solving problem 4 only

Q: . For the beam loaded as shown in the figure below, determine the following unknowns using a…

Q: Use Virtual VWork Method to solve for the vertical deflection at D in mm of the beam shown below.…

Q: From the given figure: Let P = 26KN, L = 8m, a = 3m if the equation of the slope is Ely = Pª (-+L),…

Q: Using Area Moment Method: A simply supported beam AB is shown. Assume El is constant 1. What is the…

Q: 70 mm 2 kN 4 kN 7 kN/m 100 mm 240 mm 70 mm 2 m Im 1.5 m 20 mm 70 mm 20 mm Q2)- For the beam given in…

Q: etermine the slope and deflection at point C of the beam shown. Use Area Moment Method. í thet hat…

Q: Two hard rubber blocks [G = 320 kPa] are used in an anti-vibration mount to support a small machine…

Q: Calculate the deflection at C in terms of El. Express your answer in two decimal places and do not…

A: Given data Find deflection at C in terms of EI.

Q: Using double integration method (DIM), analyze the beam loaded and supported as shown: P 150KN 1.5m…

A: Kindly refer to the attached photo. Thank you! We can double check it here:…

Q: If the midspan deflection is 50mm, and the load P = 15KN, determine the maximum length L of the beam…

Q: From the figure below determine the deflection at the overhanging section. a. Using Double…

Q: 4 KN/m 2m B 0.5 m 1 KN C a.) For the cantilever beam and loading shown, by area moment method,…

Q: 1. Determine the equations for slope and deflection of the beams shown by the direct integration…

Q: Determine The Horizontal Deflection At Point D. Use The Virtual Work Method. E = 70 GPa, Ainternal =…

Q: 2. An 8m simply supported beam supports a uniformly varying load from 0 kN/m at point C to 20 kN/m…

Q: e 5-mm thick 300-mm wide rectangul ding as shown. Using the double inte ght given that the maximum…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

3. Considering the beam loaded as shown below. Assume El - 50 000 kNm?
25KN
10KN/m
15KN.m
A B
Im 1m
Im 1m
2m
2m
2m
2m
a. What is the slope and deflection at A?
b. What is the slope and deflection at B?
c. What is the slope and deflection at C?
d. What is the maximum deflection?
e. Determine the location of the maximum deflection from the right support.
Express the slope in degrees.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

determine the deflection at C in mm using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E=80 GPa. Enter the absolute value only and round off your answer to 3 decimal places answer asap. a = 2.5 m, b 27.3 kN/m, c 23 kN. kN b kN/m BỊ 4 m 3 m
Determine the horizontal deflection of point D due to the 3-kip load on the beam as shown below. Assume the moment of inertia I-120 in and the modulus of elasticity E - 29000 kips per square inch. 3 kips B D C
Problem 32: Determine the maximum slope and maximum deflection for the given simply supported beam as shown in figure. A EI 4m 6kN B 1.5EI 4m с 6kN EI 4m D 10
Determine the deflection (mm) at point B of the beam shown below. 90 kN 5m El = constant E =200GPA 800 (106) mm4
USE DOUBLE INTEGRATION AND AREA MOMENT METHOD. THANK YOU. The roof beam of a building is subjected to the loading shown. If a 3/8-in. deflection is permitted at the cantilever end before the ceiling & roofing materials would be damaged, determine the required moment of inertia for the beam. Use E = 29,000 ksi. 24 kips 0.72 kip/f 0.48 kip/īt B 10 10
The simply supported beam is made of A-36 steel and is subjected to the loading shown in Figure Calculate the deflection at its center C using the virtual work method. Figure 60 kN 75 kN m A C 4 m 4 m B.
50. Evaluate the deflection at the centre of the beam shown in the figure using the principle of virtual work. El is same throughout. w/m E 1/2 - 1/2
Given the beam shown with P=1350N and w=720N/m, find the overhaning deflection of the beam. Express the answer in _____/EI mm of Y overhang absolute value. I NEED THE ANSWER RIGHT NOW, THANK YOU!
A load 600kN applied at point A, as shown in fig above, produces a vertical deflection at A, B and C of the beam as Ab = 10mm and Ac = 15mm respectively. What is the deflection at A when loads of 200 kN and 400kN are applied at B & C, respectively. 600KN ΕΙ + B 2L/3 A 2EI + C *4 L/3
For the beam and loading shown, determine the deflection at point C in (mm). Indicate the negative sign if it's downward. Use E=200GPa. Round off your answer to two decimals. A 00:00 0.4 m B 12 kN/m 0.8 m 120 KN 0.4 m D I W 200 x 100
Determine the Deflection at C. Use the Any Geometric Method (once for DIM, once for AMM, once for CBM) E = 200 GPa, I= 250x106 mm4. Distance are in meters. Show complete Solutions 28 kN/m 18 kN 8 kN/m. 15 kN-m A 10 Technology Druen by (nnovntion FEU ALABANO PEU DILIMAN FEU TECH Input your answer in two decimal places. Units in millimeters. No need to write down the units. Just input the numerical value with the sign. Example: if your final answer is 2.11mm upwards, just key-in 2.11 then if your final answer is 2.11mm downwards, key-in -2.11
For the beam shown, solve for the deflection (in mm.) at B. Use the following data: W = 2.3 kN/m L= 5 meters E = 357 GPa |= 305 x 10^6 mm^4 ROUND OFF TO THREE DECIMAL PLACES. INPUT THE VALUE ONLY W kN/m A В L m.