3. A House shown in the figure, wo-0.35KN/m² and the length of the house is 10m(B=10m ) , the ground roughness type is B, please calculate the wind load of everywall and roof.wind4 m7mbd.iom13 m+12m | 12m Į3Table 1 Wind load calculationWall( HeightB.Roof) /m(L)w (KN)ab1.01.06+0.8bc1.01.10-0.6cd1.01.10-0.6de1.01.01-0.6ef1.01.0-0.5

Answered: Image /qna-images/answer/8befed2a-ac2e-43e4-b95d-4cde4730e83d.jpg

Answered: 3. A House shown in the figure,…

3. A House shown in the figure, wo-0.35KN/m? and the length of the house is 10m (B=10m ) , the ground roughness type is B, please calculate the wind load of every wall and roof.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Load Analysis: A floor beam is used to support the 3-m width of a reinforced concrete slab having a thickness of 120 mm. The slab serves as a portion of the ceiling for the floor below and it’s bottom is coated with plaster. Furthermore, a 2.75-m high, 12.5-cm thick lightweight solid concrete block wall is directly over the top flange of the beam. The cross-sectional area of the wide flange steel beam is 36,645 mm2. Determine the total dead load carried by the steel beam (expressed in kN/m).
By Using slope deflection method analyze two span continuous beam ABC. Then draw Bending moment & Shear force diagram. (El constant) 100 KN 20 KN/m Sm
EXAMPLE 6.4 A concrete beam having a rectangular section 100 mm wide and 300 mm deep is prestressed by a parabolic cable carrying an initial force of 240 kN. The cable has an eccentricity of 50 mm at the centre of span and is concentric at the supports. If the span of the beam is 10 m and the live load is 2 kN/m, estimate the short time deflection at the centre of span. Assuming E=38 kN/mm² and creep coefficient = 2.0, loss of prestress = 20 per cent of the initial stress after 6 months. Estimate the long time deflection at the centre of span at this stage, assuming that the dead and live loads are simultaneously applied after the release of prestress.
Please help, I promise to give good feedback. Please do not just guess. Thank you!
Compute the total elongation caused by an axial load of 183 kN applied to a square bar, tapering from a width of 120 mm to 40 mm in a length of 10 m as shown. Assume E = 220 GPa. Answer must be in mm.
Hoi Problem II. A supporting rope is loaded with a line load q(x) = q0 between points A and B. The rope shall be stretched such that the slope of the rope at point A is zero. If (= 10 m and h = 2.3 m, determine the (a) horizontal tensile force and (b) the maximum force in the rope. q0= 36.137 kn B
1. Load Analysis: A floor beam is used to support the 3-m width of a reinforced concrete slab having a thickness of 120 mm. The slab serves as a portion of the ceiling for the floor below and it's bottom is coated with plaster. Furthermore, a 2.75-m high, 12.5-cm thick lightweight solid concrete block wall is directly over the top flange of the beam. The cross-sectional area of the wide flange steel beam is 36,645 mm2. Determine the total dead load carried by the steel beam (expressed in kN/m). Material Concrete, plain cinder Reinforced concrete Masonry, lightweight solid concrete Masonry, normal weight concrete Steel, cold-drawn Aluminum *Plaster on concrete Unit Weight - kN/m ³ 17.0 23.6 16.5 21.2 77.3 26.7 0.24 kPa
a simply supported beam with a hinge on one end and a roller support at the other end is to carry a uniformly distributed load of 25kn/m 1. determine the slope 2. determine the deflection
A simply supported beam, having the following properties: 5.5 m length, Mcr = 30 kN-m, Ig = 7000x10^6 mm^4, Icr = 3000x10^6 mm^4, uniformly distributed dead load = 5 kN/m, uniformly distributed live load = 7 kN/m, Ec = 21,000 MPa. Determine the computed value of instantaneous deflection (DL+LL)
Compute the total net deflection of the simply-supported beam with the following properties listed below. (Include the sign if it is negative) Properties: Length = 12 m Width = 334 mm Depth = 482 mm eccentricity = 136 mm %3D E 17,095.86 MPa Prestressing Force = 493 kN Unit weight of concrete = 22.25 kN/m³