SITUATION III: A reinforced concrete tied column carries dead axial load of 600 kN and a live axial load of 1200 kN. f'c = 21MPA; fy 400MPA 17. What is the factored axial load carried by the column? a. 1250 kN b. 2640 kN с. 1650 kN d. 1500 kN 18. What is the minimum dimension if it is designed to be a square column with a steel ratio of 2%? a. 350 mm b. 400 mm с. 150 mm d. 500 mm 19. Find the number of required 25 mm diameter bar that will be used if it is the reinforcement of the column. b. 10 а. 8 C. 9 d. 12

SITUATION III: A reinforced concrete tied column carries dead axial load of 600 kN and a live axial load of 1200 kN. f'c = 21MPA; fy 400MPA 17. What is the factored axial load carried by the column? a. 1250 kN b. 2640 kN с. 1650 kN d. 1500 kN 18. What is the minimum dimension if it is designed to be a square column with a steel ratio of 2%? a. 350 mm b. 400 mm с. 150 mm d. 500 mm 19. Find the number of required 25 mm diameter bar that will be used if it is the reinforcement of the column. b. 10 а. 8 C. 9 d. 12

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.
A lightweight reinforced concrete beam is 400 mm and 630 mm deep.The beam is simplysupported over a span of 7.7 m and carries a uniform dead load of 12 kN/m excluding its ownweight and a uniform live load of 12 kN/m. The beam is reinforced for tension only with six-28mm diameter bars with an effective depth to tension bars of 570 mm. fc’=20.7 Mpa, fy=344.8Mpa. Modulus of Elasticity of Concrete, Ec = 21,750 Mpa and Es = 200 GPa a. Calculate the maximum instantaneous deflection due to service loads. b. Calculate the deflection for the same loads after five years assuming that 50% of thelive load is sustained.
Solve b
A tied column having a dimension of 400 mm x 400 mm, is being reinforced with 6-32 mm diameters bars. What is the largest nominal tensile force that this column could carry? Take fc' = 28 MPa, and fy = 414 MPa. 499.437 kN 1219.33 KN 780.371 KN 1997.75 KN 944.249 KN O None of the Choices
Use transformed-area method. The cross section shown consists of a hollow concrete beam with an effective depth of 400 mm. The beam is reinforced with 4 - 16mm diameter bars placed 50 mm from the bottom of the beam. If the beam has a simple span of 6 m, what total uniform load (including its own weight) could the beam carry besides a concentrated load of 8 kN at midspan. Fc' = 7 MPa, fs = 124 MPa, n=12. 75mm 100mm & 75mm 4 D 4 150mm 200mm 50mm 50mm
2.1.Write the Equation and describe the style in the latitude of the structure
hi do you have the full solution of this step by step, im having a hard time with this
From the figure shown, 10' kN 3 m 20 kN 5 m 3 m 5 m В C a. Determine the axial force of girder GH. b. Determine the axial force of column EH. c. Determine MA, MB and Mc.
A simply supported beam, having the following properties: 5.5 m length, Mcr = 30 kN-m, Ig = 7000x10^6 mm^4, Icr = 3000x10^6 mm^4, uniformly distributed dead load = 5 kN/m, uniformly distributed live load = 7 kN/m, Ec = 21,000 MPa. a) Determine the value of Ma (DL+LL).
If the allowable shear stress is 1.25 MPa of a simply supported beam loaded by a central concentrated load P and has a rectangular cross- section (120 mm wide by 300 mm deep and I = 270 x 10^6 mm^4), then = P 60 N O zero 60000 N O 30 N O 30000 KN O
2. A concrete pedestal in the shape of a cube and is 6 feet on each side. The pedestal supports a superimposed load of 150,000lbs located on the Y-Y axis as shown in the diagram. Calculate the maximum eccentricity (e) for zero tension at the base of the pedestal. Include the weight of the pedestal using a concrete unit weight of 150 pcf. P = 150,000 lbs 3'-0" Y- 3'-0" 3' - (0" 3'-(" 6'-0"
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.