3. A cylindrical tank oriented vertically is 6 m high and 3 m in diameter. The wall has a thickness of 10 mm. If the tank is filled with water (Use Ywater = 9.81 kN/m³ and note that p= yh), (a) calculate the circumferential stress, (b) calculate the longitudinal stress. Express your answers in MPa.

3. A cylindrical tank oriented vertically is 6 m high and 3 m in diameter. The wall has a thickness of 10 mm. If the tank is filled with water (Use Ywater = 9.81 kN/m³ and note that p= yh), (a) calculate the circumferential stress, (b) calculate the longitudinal stress. Express your answers in MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2) Consider a cylindrical vessel that is subjected to both an internal pressure p and an applied torque Tat the ends (as shown). Using Mohr's circle, find the principal stresses and maximum shear stress in the wall of the tank. Assume an inner cylinder radius r = 25 inches, wall thickness t = 1 inch, applied torque T = 1500 kips-in and internal pressure p = 30 psi. [Ans. to Check opi=981.8 psi] P T T
SITUATION 8: A suspended bar system consists of two cross sections as shown in the figure. Initially its lower surface is 0.8 millimeters above the ground surface. Take E=205 GPa. 80 I1.2 m mm? 160 40 kN mm2 0.8 mm 20. Determine the stress in the 160 mm2 section when a load of 40kN is applied as shown. a. 90.8 MPa b. 204.6 MPa с. 318.3 МPа d. 147.7 MPa 21. Determine the stress in the 80mm2 section when a load 40 kN is applied as shown. а. 90.8 MPа b. 204.6 MPa с. 318.3 МРа d. 147.7 MPa |42.4 m>4
2. A rod is 0.5 m long and 5 mm diameter. It is stretched 0.06 mm by a force of 3 kN. Calculate the stress and strain. (Answers 152.8 MPa and 120µɛ)
Determine the following: a. Enclosed Area Given is a thin-walled tube with the following data: Wall thickness- 3mm b. Perimeter of the thin walled tube c. Shear flow Torque is 900 N.m Length of the thin walled tube is 1.2 m. Use G=24 GPa for aluminium d. Shear stress e. Angle of twist RI00.00 E RS0.00 0, B 400.00 Unit: mm
Example ( 8) Steel tube shaft having length 3mm and diameter 50mm subjected to axial compressive force 55 k N and change in temperature ( 100 °c drop). Find the change in length and diameter due to compound effect. Note: - E=200 GPa, u=0.3, a=11.5 Mm/ m'c
The tank shown in figure is fabricated from 0.125-in steel plate. Calculate the maximum circumferential stress in psi caused by an internal pressure of 142 psi. a = 1.8 ft. and b = 3.0 ft.
2. A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 20 ksi and the total elongation is not to exceed 0.20 in. Assume E = 29 × 106 psi.Answer: d= 0.1988 in
Q3: A hexagonal cross section bar as shown in Figure (2) below, is used as a simply supported beam. The beam carries a central load of 60 kN. Draw the shear stress distribution diagram for a section of the beam at quarter of the beam length from the left hand support. Figure (2) 25 ma 30⁰ 300 CASIO ES P DATURAL
Determine the normal stress in rod (1) for the mechanism shown in the figure. The diameter of rod (1) is 12 mm, and load P = 1400 N. Use the following dimensions: a = 105 mm, b = 210 mm, c = 160 mm, and d = 85 mm. b В P d A (1) 60° D C P 01 = МPа
Q2. Water is flowing with a velocity of 3.5 m/s through a circular pipe, knowing that the flow is laminar with a friction factor f=0.054, then: The Reynolds no. of the flow is. Given the losses within each meter of pipe is hL = 0.1 m/m , the diameter of the pipe is. Plot the shear stress within the pipe
Two solid cylindrical rods support a load of P = 22 kN, as shown. Rod (1) has a diameter of 12 mm and the diameter of rod (2) is 16 mm. Determine the axial stress in each rod. Use positive for tensile stress and negative for compressive stress. 4.8m Answers 0₁ = 0₂ = 2.7m (1) 2.2m (2) MPa. MPa. 2.2m
Two solid cylindrical rods support a load of P = 33 kN as shown. Rod (1) has a diameter of 15 mm, and the diameter of rod (2) is 12 mm. Determine the axial stress in rod (1). 5.6 m 3.8 m (1) O 141.7 MPa O 151.8 MPa O 175.0 MPa O 192.0 MPa O 208.6 MPa B P 4.6 m (2) C 3.3 m